Drawing stand, suitable for 11/13 inch iPad (Pro) - Free 3D Print Model

Search models, users, collections, and posts

LST3645_W

Household>Office

IP Report

Print Profile(2)

All

X1 Carbon

P2S

H2C

P1S

X1E

X2D

H2D

H2D Pro

H2S

P1P

A2L

V1.2 (Optimized surface printing effect)

Designer

6.5 h

2 plates

5.0(7)

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

Designer

10 h

2 plates

4.9(70)

Open in Bambu Studio

Boost

625

1902

1.8 k

1.1 k

Released

Description

Content has been automatically translated.

Show original

~~~~~~~~~~ Updated June 19, 2025 ~~~~~~~~~~

Many thanks to @Stari for their significant contribution to print profile refinement.

The updated print profile has been uploaded. Specific updates include:

Increased solid infill line width to 0.6 mm
Corrected sparse infill pattern to grid
Increased sparse infill percentage to 10%
Adjusted print speeds for various sections
Incorporated smooth Z-axis wall speed (experimental feature)

Post-update print results are shown below (using newly opened PETG-CF), with default filament parameters:

Initial inclined surface results:

Overall mid-section inclined surface results:

Overall finished product results:

Analysis of main inclined surface print failures with the old profile:
When the inclination angle is less than 30 degrees, the contact layer between the inclined wall and the sparse infill is not recognized as an overhang in Bambu Studio, resulting in insufficient speed reduction and cooling for the overhanging layer.
Furthermore, the sparse infill lines in the same location, while not identified as an overhang, are drawn prior to the solid infill, further causing “print breaks”.

~~~~~~~~~~ Original Text ~~~~~~~~~~

Drawing stand designed for iPad

Screen angle 26 degrees
Robust and stable, high load capacity
Large flat base compatible with various anti-slip pads
Strong geometric aesthetic
Luxurious materials (drawback)

Comment & Rating (98)

@KiKeKing

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

As defined, if any modification needs to be made from my point of view, it is to slightly increase the step that holds it in position as it is a bit small and when you touch the iPad it falls. My rating is entirely positive, but I would change that small detail to make it more functional if possible. Thanks to the designer for their work

Show original

@RamenDonovan

I agree. This stand is fantastic. If the step height were increased and a cutout made in the center so the USB cable could plug in to it would be an awesome upgrade.

(Edited)

@cerealsoup

Absolutely this piece must be resized. The lightest tough near the top of the ipad and it slips right off.

@KitchenKid

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

came out just fine! thanks for a good design and profile!

@olipix.lab

Boosted

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

Great print! Exactly what I was looking for! Very good angle for drawing on the iPad! Also added magnets in the back to hold my pen

@RuckusBull

Boosted

This is one of the if not the best models on this site. I created a new profile for the H2D to maintain the same print settings as the original profile and the stand came out perfect! I’ve added four silicone drops to the bottom of the stand to prevent it from slipping, and I couldn’t be happier. 10 out 10! If anyone would like me to upload the H2D profile let me know.

@user_1609943535

Boosted

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

excellent design and idea, will boost when I have my points

@user_3820270833

Thank you for uploading this deisgn. Could you make it so that the bottom bar is extruding out a lot more? when I have a case on it just slides down. Thanks in advance.

@Mykel4177568210

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

Looks good and works great. I recommend to add some rubber pads to the bottom.

@user_4203665188

Print Profile

V1.2 (Optimized surface printing effect)

excelente

@user_1912502861

Boosted

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

A+++ Thank you very much !!!

Show original

@BOOKER999

Print Profile

V1.1 (Sparse infill optimization): 0.2mm layer height, 2 perimeters, 10% infill

works great with my 11inch iPad pro

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.