Mean Arms Speed Loader Side Load - Free 3D Print Model

Search models, users, collections, and posts

Stickbird3D

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.24mm layer, 2 walls, 10% infill

Designer

3 h

1 plate

4.8(6)

Open in Bambu Studio

Boost

127

Released

Description

This is a 15+

round side loading speed loader for the Mean Arms 9MM Endo Mag PMAG inserts and the Mean Arms ExoMag. This works with both ejector and ejectorless models. The print settings are for normal use, but for the strongest version, change walls to 6 and infill up to 30-70%. Please message me if you have questions.

See my Top Load model here https://makerworld.com/en/models/1295325-mean-arms-9mm-speed-loader-top-load#profileId-1326492

Boost Me (for free)

I would appreciate your boost if you enjoy this design. Boosts allow me to purchase more filament to continue testing new designs and posting more here for your use.

Comment & Rating (19)

@brios

printed on a P1S in PLA, great work was looking for this, but the pusher handle broke right away, it is hard to get them to load, I am using an Exomag

(Edited)

The designer has replied

@Stickbird3D

Hmm. I have had no issues on my side with this. Check to make sure the mag is seated properly. It shouldn’t be that had to load them, so ensure everything is lining up correctly between the rails inside the part that holds the mag and where the rounds enter the mag. Please let me know if you see anything that doesn’t line up. When did you receive this mag?

@WaterBoyTX

it looks like you are trying this on an exomag, not an endomag?

@user_2966105805

Print Profile

0.24mm layer, 2 walls, 10% infill

Printed perfectly thanks.

@user_2004000720

Print Profile

0.24mm layer, 2 walls, 10% infill

Great idea - I did full send on 6 walls with PLA and it had trouble getting the rounds into the magazine. May need to be worked through a bit or I possibly needed to scale it up a half of a percent?

The profile uploader has replied

@Stickbird3D

Thanks for the rating. Can you see where it is binding up? If the rounds are removing a little bit of the pla with each run through, then maybe just a few uses will clear up the binding issues. If it’s too stiff and not removing any material, then maybe reprinting scaled at a half percent would do the trick. I’ve been running mine with 4 walls and no issues, so maybe that half percent will make enough room without getting the spacing too large

(Edited)

@user_2004000720

Replying to @Stickbird3D :

Yeah I think 4 walls would be plenty for this piece. I actually printed it for a friend of mine so I don't have it to break in. He had all my endomags so I couldn't even test it out before handing it over to him at the range. I just let him keep it. I'll print another for myself in the near future

@Stickbird3D

Replying to @user_2004000720 :

Haha I know how that goes. I also designed a top load version which should be under my profile if you’d like to take a look at that as another alternative.

@user_3867839198

Boosted

willing this work on .223?

The designer has replied

@Stickbird3D

it is designed to the size of a 9mm so I don’t think so. I can try and design a .223 version sometime later this week or next and will let you know when complete if you’d like

@Stickbird3D

here’s a .223 version that I just posted for you. https://makerworld.com/en/models/1332420-ar-15-round-top-load-speed-loader#profileId-1370970

@WaterBoyTX

Is this for the 'ejector' or 'ejectorless' magazines?

The designer has replied

@Stickbird3D

works on both. you might have an issue with the last round not loading properly

@shibarinest

Boosted

Print Profile

0.24mm layer, 2 walls, 10% infill

thank you so much

The profile uploader has replied

@Stickbird3D

glad you found it useful!

@user_4012927646

Is that real or fake I need real ak47 Magazine Please tell me .

@user_3193325384

Print Profile

0.24mm layer, 2 walls, 10% infill

@user_3065724330

Print Profile

0.24mm layer, 2 walls, 10% infill

@GrumpyOne

Boosted

Print Profile

0.24mm layer, 2 walls, 10% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.