Whimsical Easter Egg Tree - Free 3D Print Model

Search models, users, collections, and posts

Crafty Princess

Household>Decor

IP Report

Print Profile(3)

All

P1S

P1P

X1E

X1 Carbon

H2D

A1 mini

H2D Pro

H2S

P2S

H2C

X2D

A2L

Egg Tree (No AMS, No Supports) 0.2mm layer, 15% infill

Designer

4.7 h

7 plates

4.5(32)

Egg Tree (Print by Object with AMS) 2 Plates

Designer

4.3 h

2 plates

4.8(4)

2x plates with ams minimal waste

4.3 h

2 plates

4.5(2)

Open in Bambu Studio

Boost

482

1280

563

369

Released

Bill of Materials

Bambu Filaments

Select all

Description

Membership

Commercial License - If you want to sell prints of this model, please join my membership. Your support helps me create more detailed designs and release new models regularly.

Join

A cute and whimsical egg tree. It makes a perfect decoration for Easter time. All parts are printed separately and connected together afterwards. You can store some small trinkets or candy in the cracked egg under the tree.

No Supports Needed.
No AMS Needed.
No Glue is necessary, unless you think things are loose.
Note: The tree does sit loosely on top of the cracked egg.

Make sure your print plate is clean. The tree branches are tall and skinny and might fall over during printing if the plate adhesion is poor. Leave the auto generated brim on to help hold the tree branches on the print plate better.

Assembly Instruction Video:

If the above video doesn't work, here are the steps:

With the grass seam to the left, the tree branch with the shorter branch goes to the right-side hole. Tallest branch goes in the middle (put the middle branch in last though). You have to push and twist a bit to get the tree branches in to the grass. The branch orders should match the picture below with the grass seam to the left.
Push and twist to get the eggs onto the smaller tree branches. Both big and small eggs can fit on any branch.
Note: The tree will sit loosely on top of the cracked egg.

Boost Me (for free)

I really hope my designs bring you joy! If you like to leave a boost, I would be so grateful!

Membership

Commercial License - If you want to sell prints of this model, please join my membership. Your support helps me create more detailed designs and release new models regularly.

Join

Comment & Rating (91)

@bgloyalty

Boosted

My wife says I have too many trees; Christmas, Valentine's, St Patrick's Day,... and now Easter. Printing this was not difficult for me at all. I honestly pushed everything onto two beds and printed by object with an AMS. Grouping the colors together of course. Putting it together was a little challenging. I did end up breaking one trunk but just glued it back together, I plan on making a couple more anyway with different colors. The fitment was very tight. It was tight connecting the branches to the base but honestly that was nice because it held it very firmly. The eggs being tight on the branches was the challenging part, trying to put them on without twisting the layer lines apart. I think when I print this again I'm going to scale the eggs up just a little bit to get that hole a little bigger. Just a fraction of a millimeter would be perfect. I imagine if the Tolerance on your machine is dialed in, these wouldn't be an issue at all. Sorry for the long comment. Bottom line, this is a great print, and I'm definitely printing a couple more.

The designer has replied

@CraftyPrincess

That looks amazing! You can never have too many trees, lol. Thank you so much for sharing your build!

@bgloyalty

Boosted

Replying to @CraftyPrincess :

Number two worked so much better. Printed the eggs at 102% (snug) and 103% (slides on). Tried some super light fuzzy skin on the egg.. Not a big fan on how it turned out, I'd just keep it smooth next time. I'm having fun with this one.

@CraftyPrincess

Replying to @bgloyalty :

I love the rainbow egg vase and colors you chose for the eggs! Such a pretty combo!!

@louie74

Perfect tree to add to Easter ⭐️⭐️⭐️⭐️⭐️

The designer has replied

@CraftyPrincess

That looks amazing! Thank you so much for sharing your build!

@gquiring

Boosted

Wonderful Easter Egg tree. I had a problem with the center (longest) branch. Two print failures in a row. I decided to slow the printer down (X1C) and it printed successfully. I was using Bambu PLA filament.

The designer has replied

@CraftyPrincess

Love the little Easter creations in the background! Thank you for the boost and sharing your build!

@luckyjamie

Print Profile

Egg Tree (No AMS, No Supports) 0.2mm layer, 15% infill

Very cute! Had a hard time getting eggs on branches though.

The profile uploader has replied

@CraftyPrincess

Love the colors you chose! Thank you for sharing your build.

(Edited)

@user_2243091897

Boosted

tree branches failed first 2 tries. after turning off the aux fan those printed nicely. currently printing a 2nd one with the extra 3 eggs on 2 plates with ams. will upload profile when successfully finished.

The designer has replied

@CraftyPrincess

That looks amazing! Thank you for sharing your build! Thank you very much for the boost too!!

(Edited)

@stephasaurusrex

have made 2 of these now, no issues :) they're so cute! I did decide to glue the branches to the grass and grass to the egg for extra security

(Edited)

The designer has replied

@CraftyPrincess

That looks amazing! Thank you so much for sharing your build!

@user_1893681007

I really wanted to love this model, but the branches were very frustrating. I had many failed prints and finally added a bunch of supports, slowed the speed down and printed them individually. I still ended up having to lay the tall branch flat. After all that, one of the branches broke while putting the egg on, even though I was very careful. It's a cute tree, but not worth all the wasted filament and stress.

@user_3502716122

Print Profile

Egg Tree (No AMS, No Supports) 0.2mm layer, 15% infill

Thank you for sharing very beautiful and unique. 😊

The profile uploader has replied

@CraftyPrincess

You're welcome! Thank you for sharing your photos and leaving a rating!

(Edited)

@Airs77

Print Profile

Egg Tree (No AMS, No Supports) 0.2mm layer, 15% infill

It took me 3 times to try to print the tall stick. It failed about 1/3 of the way through the top set of branches, as others have noted. I washed the build plate, upped the bed temp by 5C, restarted the print with just the tall stick, slowed down speeds to 100mm/s and added a tree support. It still failed. I went to the comments and saw someone recommend a 15mm brim so I did that, kept the increased bed temp and downed speeds event further to 50mm/s. That finally worked

The profile uploader has replied

@CraftyPrincess

Thank you for sharing the method that worked for you! I hope it helps others too. I didn't have any problems when I printed mines, so thank you for sharing.

(Edited)

@CraftyKathy

I was so excited when I saw this. it was exactly what I have been looking for! Unfortunately, I can't get the tree branches to fit in the grass. I used .2 mm layer, 2 walls and 15% infill. Am I doing something wrong?

The designer has replied

@CraftyPrincess

Have you watched the instruction assembly video above? With the grass seam to the left, the tree branch with the shorter branch goes to the right-side hole. Tallest branch goes in the middle (put the middle branch in last). You have to push and twist a bit to get the tree branches in to the grass. The branch orders should match the picture below with the grass seam to the left. Please let me know if that helped.

(Edited)

@CraftyKathy

Replying to @CraftyPrincess :

I followed there directions exactly. No luck. Thanks for responding!

@3DGEPRINTNL

Replying to @CraftyKathy :

I had the same issue.

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Easter eggs

Modestas Skirius

19 k

4.7 k

Dragon Egg (Hidden Seam)

squinn

71.8 k

17.2 k

Easter Egg

LL-3d

11.3 k

2.6 k

Easter eggs for the Easter tree

formella

158