Meta Quest 3 / 3s stand - Free 3D Print Model

Search models, users, collections, and posts

C4RDEN

Hobby & DIY>Electronics

IP Report

GIF

Print Profile(2)

All

P1S

H2S

H2D

X1 Carbon

H2C

P1P

X1E

P2S

H2D Pro

X2D

A2L

Extended Version (0.2mm layer, 4 walls, 10% infill)

Designer

9 h

1 plate

4.8(37)

Original Version (0.2mm layer, 4 walls, 10% infill)

Designer

8.5 h

1 plate

4.2(54)

Open in Bambu Studio

Boost

724

1818

130

3.4 k

1.2 k

Released

Description

Stand for Meta Quest 3/3s

The stand has special recesses on the underside for felt pads.

Since this is my first model, I’m really looking forward to feedback and suggestions for possible improvements!

Original Version

(L x W x H)

180mm x 125mm x 215mm

Extendet Version

(L x W x H)

180mm x 125mm x 250mm

Comment & Rating (130)

@user_678113027

This has happened twice now and almost wasted a roll of filament. can someone tell me what I’m doing wrong?

@Catchonlysmiles

yeah, it happend on my side also. try to cut it. or put another support/ strong

@Jett.Glide

exactly what happened to me last night. imma slow it down cuz anything that high on supports makes me nervous.

@user_3327286192

Boosted

This works very well for my Quest 3. Tidied up the controllers nicely. Girlfriend wanted rainbow which turned out nice. Could be a bit taller (26mm) for the BOBOVR S3 Battery Strap as shown on the right headset to sit a bit better. I used 15% Gyroid Fill, tree supports on Build Plate.

The designer has replied

@C4RDEN

Thanks a lot for the great feedback! I'm really happy to hear that it worked well with your Quest 3 – and the rainbow version looks awesome! Also, thanks for the note about the height for the BOBOVR S3 strap.

@DrUltima

Were you able to print the pattern as is, or did you have to add support arms?

@user_3327286192

Boosted

Replying to @DrUltima :

Supports are needed for the headset overhangs only. Not needed anywhere else. The supports did use a lot of material. I used tree supports on the build plate only.

(Edited)

@Jett.Glide

I just decided to cut & connect it.

@Jett.Glide

Tried to remix it (of course shouting you out), but it didn't allow me to.

@user_3823993282

The back support just fell off and the entire model went into the trash

@user_1646525048

happened to me as well! First print was good. I have two headsets so printed another one. That one support fell off at the exact same height as yours. no difference in the settings and same buildplate as the first one. I´m on it again and will do some small changes in the speed and glue. Hope it works :)

@fields123

that's so frustrating

@prixypre

Print Profile

Original Version (0.2mm layer, 4 walls, 10% infill)

I just have to change the size a little.

@WhiteLeo

Boosted

Print Profile

Original Version (0.2mm layer, 4 walls, 10% infill)

Nice design, printed well. Supports - easy to remove. The top finish is not great because of the slope, but manageable. Not sure, probably it was thought about that, but a slightly slanted top to the front would work (maybe?) better, now i have to bend the Kiwi comfort band for it not to slide down. I also do not like that the controler bands are in the front. Changed seams to the back. Changed infil to Gyroid at 5%, rotated the part a bit as support are at the edge. All in all, 9.5/10. Thx!

@user_1637938043

tried this print twice same result both times

@RositaG

print failure...support issues

@user_3985205085

Print Profile

Original Version (0.2mm layer, 4 walls, 10% infill)

we had an issue with one of th w supports failing but overall it still works and it looks great. save me 25$ buying one on Amazon. so win win.

@milligan

…

(Edited)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.