Bambu Side Spool Holder X1 and P1P ARC (Updated) by Bastien

Bastien

3D Printer>3D Printer Accessories

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

0.2mm, high strengh

Designer

9.6 h

4 plates

4.6(72)

0.2mm strong for X1

2.6 h

1 plate

4.7(10)

Open in Bambu Studio

Boost

161

271

108

637

497

Released

Description

26/11/2023

Added Pushfit to the arm, there are 2 versions:

PC4-M6 shared by Micha (thanks you again)
PC4-M10 as various users ask it

Printed with @0.12mm, 3 perimeters.

----------

In this post, you'll find everything you need to equip your X1 or P1P with a side spool support fitted with a PTFE tube to guide the filament easily to the extruder.

The spool support can be either the one supplied with the printer (the metal one), or a roller using 2 608 bearings.

P1P ARC version is very similar to X1 version with the exception of a few changers needed to adapt to acrylic panels:

How to print and use:

Make sure the print is strong and rigid, I've printed mine with 4 perimeters, 0.2mm layer height 5 top/down layers, cubic (or gyroid) infill.

The filament guide just fits into arms, you can glue it but it's not necessary

PTFE tube is pushed into the hole, tolerance may vary depending on your filament and printer calibration

Plate 1 is P1P ARC original support

Pate 2 is P1P ARC roller support

Plate 3 is X1 original support

Plate 4 is X1 roller support

Comment & Rating (108)

@PrinttXOldAccou

Print Profile

0.2mm, high strengh

Works very well and printed perfectly in petg

@user_2949356595

Boosted

0.2mm, high strengh Printed without any problems. as I don't find the way to give the 5 stars via comment directly on the website, here they are: ⭐️⭐️⭐️⭐️⭐️ PS: I noticed in the print profiel that plate 1 and 2 are for the X1 and plate 3 and 4 are for the P1P ARC, contrary to what is written above (at least the naming of the objects say so in the profile)

@bondbuilt

Boosted

Print Profile

0.2mm, high strengh

Bambu grey came out great to match the printer.

@HermannSeGerman

Print Profile

0.2mm, high strengh

Perfect! Printed with Bambu blue-ish metal PLA. Had a bit of over extrusion on the holder's overhang but it's on the backside so it's fine. Probably due to the filament and not her model itself. The bearing are loose enough to easily remove them, the holder for the roller fits tight in it's slot. The filament guide works great with the Y adapter and tried it with TPU. No problems at all. Thank you for this great and simple model!

@user_1571989700

Perfekt for non-AMS filaments & spools! Printed with PLA: - Sunlu Silk PLA Silver - Devil Design PLA Raspberry Due to the shrinking of Silk PLA, the fit was very loose and I used some Uhu Allplast to glue the three parts permanently together. Thank you very much!

@jeff.cassidy.jc

Print Profile

0.2mm, high strengh

I liked the design, very simple and elegant.

@madizmo

Print Profile

0.2mm, high strengh

Works great!

(Edited)

@Bottega.co.nz

Boosted

Print Profile

0.2mm, high strengh

it came out great and fits together nicely. highly recommended.

(Edited)

@SquatchOps

Worked perfectly! totally saves me time and space. Thank you!

@GenericUser

Print Profile

0.2mm, high strengh

Good design, prints well in PETG with std supports. Fits in all the right spots, works with the smoothy bowden Y connector, sturdy enough loaded with full roll.