Phone Stand (No AMS needed)
Boost
1087
1609
761
Print Profile(10)
0.2mm layer, 2 walls, 8% infill
Designer
1.4 h
2 plates
Merged Accent Version for AMS
Designer
1.9 h
1 plate
Accent Profile with two more tolerance options
Designer
28 min
2 plates
Brim,0.2mm layer, 2 walls, 8% infill
1.6 h
2 plates
Click to see more
Boost
1087
1609
761
20
6 k
8.2 k
Released
Description
01/03/2024 Added a merged accent version for AMS printing
Added an accent profile with two more options for people who are having issues with fitting them to holder.
The stand is designed to hold the phone with or without a case. Accents on the side are printed separately and fitted in after being printed
No AMS is needed for dual-color print.
Accents are a tight fit so position them into place and push down on a hard flat surface for a flush fit.
Inspired by @libb_s - you should check out some of their models
If you like this design I now have a MagSafe version and an Apple Watch Stand uploaded to Maker World
https://makerworld.com/en/models/132925#profileId-144122
https://makerworld.com/en/models/137254#profileId-149348
Comment & Rating (761)
All
Print Profile
0.2mm layer, 2 walls, 8% infill
the colors caught my eye, so i gave it a go, printed in white Ziro matte PLA at sport speeds and used a red matte PLA for the accents, they are a tight fit but thats in a good way, looks great and works great too.
only suggestion would be to mirror 1 piece on the second plate so you can get the same top or bottom surfaces facing outwards when its all assembled.
(Edited)
The designer has replied
7
Reply
looks good, sorry I thought I had mirrored the accents. will change my profile
0
Reply
Profile changed to have mirrored accents
(Edited)3
Reply
Nice choice of color
0
Reply
Great job !!!
The designer has replied
3
Reply
Love the red and the yellow versions
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
Sehr schönes Modell und perfektes Druckprofil und Druckergebnis. Habe nichts abgeändert. Das kleine (bei mir weiße) Profile muss mit bisschen Kraft und Gefühl in die Halterung gedrückt werden.
passt hervorragend und kann nicht rauslassen.
3
Reply
Print Profile
Print Sequence Sliced by Object - 0.2mm layer, 2 walls, 8% infill
very nice.
3
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
This Design is a true piece of art - i adore it! ❤️
The designer has replied
2
Reply
Thank you! That means a lot.
0
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
printed well and i love the design. but i am going to have to reprint it. the brim on the color piece didn't remove at all and even with clean up, it looks junky now. here is hoping printing without a brim works or maybe change the distance or use support filament, if it works for that.
Edit: from 4 to 5 stars. pro tip, print inserts without brim.
(Edited)
The designer has replied
0
Reply
it actually prints fine without a brim, I added one because more people would have issues without it. Try printing without but if you have and X1 or P1S make sure you turn the aux fan completely off
0
Reply
Replying to @Reckit
thanks. printed a couple of colors on the A1. No issues.
0
Reply
super nice model, thank you!
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
top
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
perfect
1
Reply
Print Profile
0.2mm layer, 2 walls, 8% infill
I love it! exactly what I needed!
1
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld