Battery-powered Rotating Base - Free 3D Print Model

Search models, users, collections, and posts

Jesús Reina

Tools>Other Tools

IP Report

Print Profile(1)

All

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 3 walls, 25% infill

Designer

7.5 h

3 plates

4.8(6)

Open in Bambu Studio

Boost

202

414

293

Released

Bill of Materials

List other parts

Bateria 18650 x 1: https://a.aliexpress.com/_Eu79fdw
Soporte bateria 18650 x 1: https://a.aliexpress.com/_ExEQZXO
Modulo cargador de bateria x 1: https://a.aliexpress.com/_EGnqEAs
Rodamientos ZZ 608 x 4: https://a.aliexpress.com/_EQo9RfO
Controlador de velocidad de motor x 1: https://a.aliexpress.com/_ExGS1cs

Description

Content has been automatically translated.

Show original

Simple 3D-printable rotating base to showcase your models in motion. Assembly is straightforward; tolerances are built into the design. You will only need a soldering iron, hot glue gun, and the following assembly components: 4 ZZ 608 bearings, a USB Type-C charging module, an 18650 battery and battery holder, a dual-gear motor, and a speed controller. It can be printed in PETG, but 3 walls with PLA is sufficient. I've tested it with two kilograms of filament on top, and it rotates without issue. Display your creations with a self-made rotating base. Enjoy!

base

rotating

plataforma

Comment & Rating (32)

@user_266949299

Print Profile

0.2mm layer, 3 walls, 25% infill

excellent the only thing is that the motor is very close to a bearing, I think that could be improved otherwise excellent

(Edited)

The profile uploader has replied

Show original

@JesusReina82

If you are right, I could rotate it a bit, but once I tested that it rotates well, I put a drop of glue on the base of the bearing so it wouldn't move and in a year it hasn't given me any problems. By the way, yours turned out very clean. Congratulations. And thank you

(Edited)

Show original

@user_266949299

Replying to @JesusReina82 :

Hello, if everything is glued, it's that minimal detail and that the bearings do not go all the way to the end of the guide because it rubs against the teeth of the base. but if you glue everything, it works perfectly. Excellent design Thank you very much!!!!!!

(Edited)

Show original

@Xmos

Printed, but I see a lot of rattling in the movement. Things on top are shaking. The dual shaft motor dances in the gap for the and I think it rubs in the housing gap of the other shaft. I don't know if it's a problem with my assembly or if it's generic. I will try to make an adjustment to achieve smoother movement

(Edited)

Show original

@RMarcolino

Does anyone have a link to the motor? And the yellow bell

Show original

@user_2932616626

Boosted

Hello could you help me with the cable connection

The designer has replied

Show original

@JesusReina82

Sure What problem do you have I test it outside before installing it inside the base

Show original

@JesusReina82

The connection is shown in the photo Assuming the red wire is positive and the black or blue is negative first test the circuit directly from the motor to the battery bypassing the regulator and the charging base Then when you see that it works connect the rest From the battery holder it goes to the central pads of the charging board and exits through the external pads Connect the current regulator as shown in the photo and once you see it working mount it on the base

Show original

@user_2932616626

Boosted

Replying to @JesusReina82 :

I already solved it everything excellent

Show original

@Jubalcoy

A shame, because it is more or less well made But the motor almost touches the bearing, then the three bearings that hold the platform, I glued them with glue and now it turns out that when putting the platform it rubs against the platform gear Result, reprint the bottom part because by gluing it with loktite it is impossible to unstick it without breaking it

The designer has replied

Show original

@JesusReina82

I am very sorry that you have to repeat it. If you read what I wrote, I said that hot glue is needed, not Loctite or cyanoacrylate. It is true that if you glue the bases of the bearings to the bottom, it rubs, but if you try it before gluing it and glue it with hot glue, you will have no problem. I have mine for a year and it's still there. I haven't touched up the design because people don't boost it and it's not worth it for me. Anyway, thank you for downloading it and enjoy it

Show original

@Jubalcoy

Replying to @JesusReina82 :

I printed it again and attached the bearing supports further out, and it works there. But that little glitch needs to be mentioned, because I got careless and messed up. But everything is fine now, thanks

Show original

@Josguto

Could you furnish an AliExpress link for the motor as well

The designer has replied

Show original

@JesusReina82

I found this on AliExpress: €3.78 | 1-20 Pcs Dual Shaft Gear Motor, DC 3-12V Smart Car Motor for Smart Car Robot, 1:48 Plastic TT Motor Tire Wheel https://a.aliexpress.com/_EHFjV0m

Show original

@JesusReina82

Sorry for not replying sooner

Show original

@pcdefcon

Thank you very much, the set and design are excellent Functionality is excellent

The designer has replied

Show original

@JesusReina82

Many thanks to you, my friend. Enjoy it

Show original

@JesusReina82

Thank you for your rating Enjoy it

Show original

@Mario_DM

Boosted

It turned out excellent and very functional

Show original

@Jubalcoy

Print Profile

0.2mm layer, 3 walls, 25% infill

Except for the error we've already discussed, everything else is fine

Show original

@Agusreviriego

Hello The connection in the photo is not entirely clear I understand that from the battery holder they go to the center pads of the charger and at the ends they go directly to the regulator right? It's the only doubt Thank you and a very good model

Show original