Padel Racket Stand Display - No hardware - Free 3D Print Model

Search models, users, collections, and posts

ArmenioMarques

Hobby & DIY>Other Hobby & DIY

IP Report

Print Profile(1)

All

P1S

H2S

X2D

P1P

H2D

H2C

P2S

H2D Pro

X1 Carbon

X1E

A2L

Simple (NO LOGO)

Designer

4.4 h

2 plates

4.9(12)

Open in Bambu Studio

Boost

222

506

566

276

Released

Bill of Materials

Bambu Filaments

Select all

PLA Basic

PETG HF

Description

Padel racket holder for table or other surface. It is designed to hold and support the weight of the racket without it falling or breaking. I recommend printing it on PETG for extra strength, but PLA should do the job.

I advise you to add a little glue and fit the pieces together so that they are secure. You don't need much, just to hold it in place. Put the glue inside the hole so it doesn't run out.

We recommend adding a sponge pad to this model where the racket is secured. This allows you to adjust the thickness of the support to fit the racket, preventing it from sliding forward or backward. As a result, the holder is compatible with all or nearly all models.

Boost Me (for free)

It's free and I appreciate it! if you can, leave 1! or 2 :D

Membership

If you want to sell my creations, here's a super-cheap option. If you have any questions, just send us a message

Join

Enjoy!

Comment & Rating (57)

@mathiasdela

Boosted

Print Profile

Simple (NO LOGO)

The user changed one piece that has been a issue and now its fine!

(Edited)

The profile uploader has replied

@ArmenioMarques

Overhangs? 😅

@ArmenioMarques

I dont think you printed this right… this model has no overhangs!

@mathiasdela

Boosted

Replying to @ArmenioMarques :

the filet of the rod is so Big that there is overhangs. I will post a picture.

@tehHammy

Would you be able to large this part inward - so as to ix the common issue with the design that padel's tend to slip out.

The designer has replied

@ArmenioMarques

Hello We recommend adding a sponge pad to this model where the racket is secured. This allows you to adjust the thickness of the support to fit the racket, preventing it from sliding forward or backward. As a result, the holder is compatible with all or almost all rackets.

@tehHammy

Replying to @ArmenioMarques :

ya no - thanks - the lips dont hold the racket - it should

@tehHammy

Replying to @tehHammy :

think a few people mentioened it falls out - the lips does not hold it - I have a few rackets - they all fall out if you cannot is fine - but it need the triangle to be larger on the top to prevent the tilting of the racket. It is very evident from a few posts

@Fem3D

Boosted

Great model! Thanks for sharing it

The designer has replied

Show original

@Dvnn

Boosted

Show original

@tehHammy

Replying to @Dvnn :

Not sure how your Bullpadels stay there - did you tweak something - because my 2026 Neuron Edge 02 sits in there but tilting back it just falls out - front lips not deep enough.;

@ArmenioMarques

Replying to @tehHammy :

@filipernogueira

I printed it, tested it with 3 racquets, and it doesn't hold any of them

The designer has replied

Show original

@ArmenioMarques

Good afternoon you have to hold it so that mine are safe put a sponge inside that always helps, so they don't wobble

Show original

@ArmenioMarques

Do they fall forward

Show original

@filipernogueira

Replying to @ArmenioMarques :

Back

Show original

@user_2618540083

This part isn't printing correctly, it seems to be missing a support for the interlocking section, am I doing something wrong? I have a Bambu Lab A1

The designer has replied

Show original

@ArmenioMarques

Hello Yup, you need to enable supports

@Dvnn

Boosted

Replying to @ArmenioMarques :

How do I enable supports? I just printed it and experienced the same issue."

@user_2229396980

Tried with 3 rackets, none of them hold. The top is outweighed and the racket falls out

The designer has replied

@ArmenioMarques

Hello what do you mean? I find it very strange because I tried with several and everything was ok Is everything well put together? if the problem is that it rotates a little in the holder, add a bit of foam until it stabilizes in the desired position. If you want, send a video of what happens to armenio.henrique.marques@gmail.com and I'll be happy to modify the model so that it works with all rackets.

(Edited)

@tehHammy

Same just printed - the racket does not stay within the holding piece. Nothing about putting it together - the racket slides in and as soon as you leave it - the racket pushes past the holding part. Only means we need that one part to be more closed.

@ArmenioMarques

Replying to @tehHammy :

@KlaverSports

Boosted

Thanks, it’s really nice.

The designer has replied

@ArmenioMarques

Thank you :)

@tehHammy

Printed fine - just the part holding the padel / racket does not keep the racket in place and thus a little unsafe to leave it un attended.

The designer has replied

@ArmenioMarques

@user_3055880599

what app do you recommend to straighten the mast? I wanted to adjust the width too for another type of paddle

The designer has replied

Show original

@ArmenioMarques

Hello I made it in Fusion 360

Show original

@user_3054002011

Print Profile

Simple (NO LOGO)

Gute Datei

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.