Wallerholz Catfish Clonk - Free 3D Print Model

Search models, users, collections, and posts

Chris

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(7)

All

H2D

P1S

X1E

X1 Carbon

P1P

H2D Pro

H2S

P2S

H2C

X2D

A2L

30mm Teller - 0.2mm layer, 2 walls, 15% infill

Designer

3 h

2 plates

4.6(14)

45 mm Teller - 0.2mm layer, 2 walls, 15% infill

Designer

3.7 h

2 plates

5.0(3)

35 mm Teller - 0.2mm layer, 2 walls, 15% infill

Designer

3.6 h

2 plates

4.7(3)

15mm Teller - 0.2mm layer, 2 walls, 15% infill

Designer

1.9 h

2 plates

5.0(2)

Click to see more

Open in Bambu Studio

Boost

141

263

405

240

Released

Description

Content has been automatically translated.

Show original

Elegant wall-mounted wood-look shelf.

Boost Me (for free)

Hi everyone! I invest considerable time and effort into these models. A boost, like, or a short review would therefore be greatly appreciated. It might even save some of my hair in the process :D

I initially printed it in PLA due to a lack of wood-colored PETG. PETG would likely be more durable, but honestly, with such minimal material usage, it's not a significant concern.

The length is approximately 30cm, and the shelf measures approximately 40x45cm (oval).

I've now added various shelf sizes. The overall length may vary slightly, as the available space on the plate differs depending on the shelf size.

I've split the design in the middle to enhance stability and enable faster printing without extensive supports.

I've also incorporated small squares to facilitate flush gluing. Supports are necessary for the recesses, but these can be easily removed with a small screwdriver.

If you require a different handle angle, or a larger/smaller shelf, please let me know. I'm happy to create it for you.

Comment & Rating (42)

@Maru9903

Print Profile

Flat plate 0.2mm layer, 2 walls, 15% infill

The two seperate pieces does not go flush, would have to sand a little the connecting cubes. (Yes its pushed all the way down)

The profile uploader has replied

@Cross213

I apologize if it doesn't fit exactly I initially had this exact problem and essentially fixed it by slightly scaling the squares these are unfortunately created by Bambu Studio itself sometimes there are still support remnants in the recess

(Edited)

Show original

@Maru9903

Replying to @Cross213 :

What kind of glue did you use to glue them together?

@Cross213

Replying to @Maru9903 :

this one

(Edited)

@Rom_Ka

Print Profile

30mm Teller - 0.2mm layer, 2 walls, 15% infill

The model is good, however, I am not at all satisfied with its functionality, I will stick with my purchased ones

The profile uploader has replied

Show original

@Cross213

Thank you for your honest feedback and the five-star rating nonetheless The functionality definitely needs improvement, and I am already working on it While it does work fundamentally, one simply needs to strike the object somewhat differently than usual

Show original

@Rom_Ka

Replying to @Cross213 :

I would happily test it again if you have something new

(Edited)

Show original

@Cross213

Replying to @Rom_Ka :

It will take a little while, I currently have limited time for modeling. But I think I know what I need to change 👍

Show original

@FerdinandHecker

Print Profile

30mm Teller - 0.2mm layer, 2 walls, 15% infill

Top, does what it should. 34€ at the fishing shop, peanuts here

The profile uploader has replied

Show original

@Cross213

I am delighted if you like it

Show original

@PhilippSt

Print Profile

30mm Teller - 0.2mm layer, 2 walls, 15% infill

I experienced extreme stringing, but that might have been due to the filament

The profile uploader has replied

Show original

@Cross213

Thank you for the review Stringing is 100% due to the filament or nozzle I've already printed more than 20 of these without any stringing whatsoever ☺️

Show original

@PhilippSt

Replying to @Cross213 :

I hadn't experienced this with other models using different profiles, but it's certainly not impossible

Show original

@user_2381903544

Boosted

Has it been tested in water, and is a flat-headed version available

The designer has replied

Show original

@Cross213

Message me privately with your exact requirements, then I will upload something new I haven't yet been to the water

Show original

@user_2381903544

Boosted

The pin is out

Show original

@Blackeclipse

Boosted

Unfortunately, one part did not print flat for me, it was upside down, what is the reason for this?? also the head is more like 55mm than 35mm, which is okay.. just adjust the description

The designer has replied

Show original

@Cross213

Thank you for the hint. indeed, one of the two halves is suddenly printed upside down. I tested all the profiles back then, something must have happened in between. I will correct that! sorry!!

Show original

@J.D4S

Print Profile

30mm Teller - 0.2mm layer, 2 walls, 15% infill

Assembly worked well, but unfortunately not yet tested in water

Show original

@Northsider

Print Profile

30mm Teller - 0.2mm layer, 2 walls, 15% infill

Printed well, haven`t tested yet. Thank you!

@user_2336919037

what does it do?

@Cosmin99

It looks great printed. I tested it in the bathtub but the sound doesn't seem to be strong and loud. Could it be that I didn't have a good position to hit it or has anyone actually tested it while fishing?

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Fishing Clonk

just_nikolay

371

337

Redtail Catfish Flexi

Bruddz

221

372

Flathead Catfish Mount

Fish Prints

997

377

Flexi Hybrid Catfish

FilliFuu

3.7 k

2.3 k