Nintendo Switch/Switch 2 Game Cartridge -Clamshell - Free 3D Print Model

Search models, users, collections, and posts

Average3DPrints

Toys & Games>Other Toys & Games

IP Report

GIF

Print Profile(1)

All

X1 Carbon

H2D

P1S

P1P

X1E

H2D Pro

H2S

P2S

H2C

X2D

A2L

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

Designer

4 h

1 plate

4.4(77)

Open in Bambu Studio

Boost

521

1499

105

1.3 k

767

Released

Description

Boost Me (for free)

If you find this model useful, boost it please! It's free to you and helps me continue to design new models to share with the community.

This is an improved version of my previous build. This build will use 4 - 4x2mm magnets. The design is with a print in place hinge. If you have issues with the hinge not working correctly, you likely need to calibrate your filament. I have had no issues using PLA with this design.

Comment & Rating (105)

@Deevlo

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

I wish it were the same size as a real game case. That would have made it perfect. The profile itself is great if you don't mind it not matching.

The profile uploader has replied

@Average3DPrints

I could potentially make one where it is the same size. Is that what you mean by not matching?

(Edited)

@Deevlo

Replying to @Average3DPrints :

Sorry yes, that's what I meant. I was hoping it'd fit in a stand with the other boxes like this: https://makerworld.com/en/models/425285-nintendo-switch-1-2-game-case-holder#profileId-328871

@Average3DPrints

Replying to @Deevlo :

Ok, let me see about expanding the model. I will create a different print profile for it.

(Edited)

@AlbertQ91

This design is my favorite one I've seen so far on here. The print came out perfectly. The only issue I have is that the games are way too hard to get out. I can barely get them out, but my kids cannot. Has anyone tinkered with it and solved that issue? I'll also try to tinker with it myself. Thanks @Average3DPrints

The designer has replied

@Average3DPrints

I can see about giving more space in the slots.

@AlbertQ91

Replying to @Average3DPrints :

So I tinkered with the print by using a file to sand down the tiny protruding bumps that hold the games in the slots. That did the trick!

@boafett

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

great print Thanks 🤩

Show original

@T1gr0u

Boosted

Very nice, thank you :)

The designer has replied

@Average3DPrints

Thanks for uploading the picture and thanks for the boost!

@EA_pilot

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

I’ve been looking for a place to store all my switch games and now I have it.

(Edited)

@maxxe_LP

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

Hello thank you very much for this really nice

Show original

@Vulpes_Vulpes

Boosted

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

Very nice model, slim and it looks awesome! The fit came out a bit tight (for cards and magnets), however still better than too loose. Boost given! :-D

@cliffback

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

Great print, but not sure about the tolerances. Standard bambu lab profile and PLA gave a case with cartridges impossible to remove without an external tool, like a knife or something.

@Malica

Print Profile

Improved Hinge - 0.2mm layer, 2 walls, 15% infill

Sehr schönes Modell!

@LivBigSki

Boosted

Given you a bosot cause i like the design and cause its useful. in all honesty i printed it and when i went to clasp it together, the hinge cracked... one half did in two spots. so not it doesnt open nicely, but maybe i was just too forceful. i glued 1 of the pieces that cracked back on it so its okay now. my magnets are too small for the holes, but i super glued those in aswell. thanks for sharing this even though mine was a little rocky, i dont think its cause of your design. its my own fault.

The designer has replied

@Average3DPrints

Thank you! I have been thinking of making one that uses metal dowel pins for the hinge as well. I printed it perfectly several times on my X1C, but I did have to tune my filament on the P1S.

@DOCDODJ

Replying to @Average3DPrints :

a suggestion would be instead of a pin, maybe a filament can be used. also printed one and the hinges cracked. I would also suggest maybe to make changes in orientation or strength?

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.