Auspicious Cloud Extendable Sword - Extended Detachable Version - Free 3D Print Model

Search models, users, collections, and posts

SKY-Yara

Toys & Games>Other Toys & Games

IP Report

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.24mm layer, 3 walls, 15% infill

Designer

17.2 h

3 plates

4.9(12)

Triple perimeter 0.2mm layer, 2 walls, 10% infill

Designer

6.1 h

1 plate

5.0(5)

Auspicious Cloud Retractable Sword - Blade Improvement

Designer

10.6 h

2 plates

5.0(2)

Open in Bambu Studio

Boost

223

501

636

271

Released

Description

Content has been automatically translated.

Show original

After much anticipation, the extended, detachable version is finally complete. An additional blade section has been added, increasing the length to 175mm for perfect compatibility with mini models. The tail features a detachable threaded end cap; both ends have been symmetrically widened to maximize blade storage space.

Extensive printing tests revealed that using the default classic wall generator style may occasionally prevent the thread from tightening. This is due to numerous discontinuities in the thread area, resulting in unusual protrusions. If this occurs, carefully remove the protrusions with a sculpting tool. Switching to the Arachne mode will mitigate this issue in future prints.

It is recommended to print the separate-part version. Compared to the one-piece version, it omits the support brim on the blade tip, eliminating the need for manual trimming and preventing potential hand injuries. The one-piece version is more suitable for mass production.

The updated blade improvement version optimizes the blade gap, resulting in a thicker blade tip and theoretically enhanced strength. However, the smaller gap between blades leads to variations in extension length depending on the filament used, necessitating post-print adjustment and compensation. Minor internal handle variations exist; mixing this version with the original is not recommended.

Boost Me (for free)

Your support fuels my continued creation

Comment & Rating (22)

@Elijahsprints

Print Profile

Auspicious Cloud Retractable Sword - Blade Improvement

printed great. I did not expect it to be a single print

@user_3160665437

Print Profile

0.24mm layer, 3 walls, 15% infill

Printed perfectly

@user_547091587

Wasted so much of my filament don’t print this if you’re using the A1 mini

The designer has replied

@SJ105X

This model weighs only 120 grams, relatively little material compared to other swords, if the print fails, check if the bed adhesion is poor or if there is a parameter issue, it is recommended not to print too fast, the A1 series platform moves back and forth so stability is not very good

Show original

@user_547091587

Thank you for your advice. I might try that.

@user_3045956948

Print Profile

0.24mm layer, 3 walls, 15% infill

works great just don’t smack anyone with it only stab

@scrappunk

Boosted

Print Profile

0.24mm layer, 3 walls, 15% infill

It is perfect

Show original

@user_3898286391

Print Profile

0.24mm layer, 3 walls, 15% infill

@dogsy

Print Profile

Triple perimeter 0.2mm layer, 2 walls, 10% infill

@Qwyzz

Print Profile

Triple perimeter 0.2mm layer, 2 walls, 10% infill

@Tomek77

Print Profile

0.24mm layer, 3 walls, 15% infill

@Ian_520

Print Profile

Triple perimeter 0.2mm layer, 2 walls, 10% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.