Search models, users, collections, and posts
Bio
Trying to learn CAD and create useful prints for people's daily lives!
Achievements
MakerWorld Guardian
This badge has expired
Share
0
0
0
The post is no longer available
Worked great and fit more than a weeks worth of q-tips for a last minute trip of mine.
Share
0
0
0
Was an absolute pain to get these things together without glueing the 3 pieces together. A majority of them did not snap together as you mentioned in the description. However after printed what felt like 1000s of these, I was finally able to get a box full.
Share
0
0
0
printed on my H2D with basic PLA, came out great, I will suggest one thing. please remove the concave corners on the bottom of the press. I left cards in for over a day and due to those corners on the bottom, it curved all of the cards. This is an easy fix and this works great so I won’t give it less stars but please fix this as now my $400 collectors pre con has all curved corners.
Share
0
0
0
Printed on an H2D, with PLA, not sure if it was filament or what, but I printed the 24x14 (standard size) and it was not able to fit my standard play mat. This could be due to the thickness but it was standard thickness so I’m not sure. A bit disappointed as it was a 20 hour print, but I’ll just give it away, it looks nice.
Share
0
0
0
Printed on my H2D with basic PLA and they came out great! Thank you!
Share
0
0
0
Printed on the H2D with basic PLA at .2 layer height. Print came out well and the top hook fit snugly, however the bottom part did not seem to fit as snugly, I’d assume that the weight of the phone would keep it in place, however I haven’t use the mount while cycling so I’m just going off looks at the moment.
Share
0
0
0
Printed on my H2D and it came out great.
Share
0
0
0
Printed on my H2D, and could not be happier. came out great, and works as intended!
Share
0
0
0
Printed on my H2D with the creators profile, the “bottom” side (side with supports, that contacts the rail the most) had issues with removing the supports and kinda messed up that side of the print. seems useable however did not print as intended, seems the support had to much adhesion to the print on the creators profile.
Share
0
0
0
The post is no longer available
printed on my H2D with Inland Basic PLA, very happy with it, just waiting on the magnets to get delivered!
Share
0
0
0
Share
0
0
0
Hello All!
The Locker Vest Hanger is my first CAD creation, so thank you for your patience and wisdom!
I noticed a majority of my partners and I used tough hooks, zip-tied to our lockers, to hold our internal and external vests. I decided to create a locker hook suitable for supporting the weight of an external carrier or internal vest, accommodating vests for both the smallest and largest people in my department.
Locker Vest Hanger
9
38
Share
0
0
0
printed on my H2D with 0.08mm layer height. Not sure if the layer height caused this issue however the two middle pieces would not flushly connect with each other, everything else connected seamlessly.
(side not if you have a usb cover, it may interfere with this model) <- it did for me, so I had to remove my usb cover.
quality is awesome though, I was surprised that air could go through as it almost seemed like there were no gaps for air.
Share
0
0
0
The post is no longer available
Share
0
0
0
Came out very good once I selected the correct profile, I by rookie mistake hit the PETG profile someone posted and it was a massive waste as the AI detection didn’t catch the spaghetti mess while I was sleeping!
Share
0
0
0
Printed on my H2D, and it came out great. Took a little over 10 hours. I realized after that it did not have spots for D batteries, however I was able to fit 4 of them into one of the circle spots.
Share
0
0
0