Massage Roller (Fully printed) - Free 3D Print Model

Search models, users, collections, and posts

SavageLau

Toys & Games>Other Toys & Games

IP Report

GIF

Contest Winner

Fidget Toys Design Contest

Print Profile(10)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

new roller! updated, easier install

Designer

2.3 h

1 plate

4.8(570)

All parts included, Stable print configuration

Designer

2.6 h

1 plate

4.8(756)

a1mini, new roller! updated, easier install

Designer

2.5 h

1 plate

4.7(143)

a1mini, all parts included, easy remove brim, stable print configuration.

Designer

2.6 h

1 plate

4.7(67)

Click to see more

Open in Bambu Studio

Boost

4097

9261

1758

358

15 k

13.1 k

Released

Description

If you want a commercial license, join my Commercial license club.

Membership

If you want a commercial license, join my Commercial license club.

Join

Boost Me (for free)

Fully 3d printed parts. Super smooth. No other hardware needed. The fitting for rods and cap are permanent, you can try to take it apart, but most likely it will break.

So, one day my boss saw the planter pot and she said that would be a great massage thing.

I had to say yes, becasue she is “boss”. so, I combine two stuffs on my design inventory, filament roller for Ender 3 and this planter pot.

And the final outcome is this. Lol

That's how you printed it: or just use my print file. ADD Brim!!!!!!

Comment & Rating (1758)

@Infill3D

Print Profile

All parts included, Stable print configuration

The idea is cool, model is good. Small improvement, if you cut a slot in the middle like this, the assembly will be easier and it flexes enough to bear the stress.

The profile uploader has replied

@SavageLau

great suggestions.

(Edited)

@DebbieO

I cut the slot as suggested and it worked perfectly! Thanks.

(Edited)

@min.nim

ok, I printed a roller with tpu, only 2 wall loops. but it is insanely tough and real nice to touch with the round dots. now what type of material should I used for the rods? pla petg abs?

The designer has replied

@SavageLau

petg would be better. normal PLA should work great too. Silk might have stength issue.

@min.nim

Replying to @SavageLau :

tpu and petg- feels really good! I feel like I can mass produce it now. lol

@SavageLau

Replying to @min.nim :

nice, but no commercial tho. lol

@min.nim

anyone having the issue that the rods are not strong enough and break when it is dropped on the hard floor?

The designer has replied

@SavageLau

I did, if the cap was hammered in in an angle. Shear stress will break it easily, especially for silk filament.

@min.nim

Replying to @SavageLau :

any suggestions on how to improve the strength?

@SavageLau

Replying to @min.nim :

more infill, or carefully hammered down in 90degrees angle from top. I just break another two... hammered it while watching moive.

@user_2564677313

Boosted

Print Profile

a1mini, new roller! updated, easier install

Printed really nicely and is fun to use! Initially, I couldn't assemble it properly, there was a bit of a gap and that made it more noisy to use, there was too much of a clickity clackity sound. After looking at the photos here I realized that the gap on the side was meant to be smaller and I used more force (stepped on it... ) to assemble it properly. There is still some noise when using it but it's much better now.

@Mjercer

Thanks! Couldn’t get it to snap closed but stepped on it like you said and it went great

(Edited)

@user_1168785507

Replying to @Mjercer :

stepped on it how i am trying to get it to press together so i dont have to glue it

@Mjercer

Replying to @user_1168785507 :

I just put it on the ground with the rollers standing up vertically and the end caps in place on both ends. then I stepped on the piece that needs to go in and hold them together. I did it slowly with a little more pressure/weight until it snapped in and I heard it. hope this helps!

@epicflail

Print Profile

All parts included, Stable print configuration

this thing came out great. it will be a great stocking stuffer.

The profile uploader has replied

@SavageLau

have fun!

@user_1168785507

how did u get it to snap together

@epicflail

Replying to @user_1168785507 :

It pushed the ends on. Didn't really take much force.

@Idiosyncrasy

Printed this for grandma (apparently fidget toys can be good for people with dementia) Everything went smoothly with designer profile, but I think I reduced the brim width. It works, I'm not sure I get the point of that or why so many people like it. Like... is it a toy ? or a massage thing ? Am I supposed to massage my hand with it ?!? I'm a bit confused as a male that doesn't know massages at all. But, it works and it's reasonably fun to roll in your hand so it does the job I guess. Thanks OP !

(Edited)

The designer has replied

@SavageLau

I don't know why it called massage, my boss come up the idea and name. She think it helps blood flow on you hand while you playing it.

@user_1326132925

It's about finger dexterity with these "toys" especially with dementia it is good if your grandma is encouraged to do something to move with fidgets for example the fingers must also be in motion which utilizes and trains mobility coordination and muscles it will certainly do her a lot of good such exercises for the fingers are also very good for arthritis the joints must be kept in motion

Show original

@mker17

Print Profile

All parts included, Stable print configuration

Cool looking fidget.

(Edited)

The profile uploader has replied

@SavageLau

nice color!

@CouzHub

Print Profile

new roller! updated, easier install

Nice finish, great textures

(Edited)

Show original

@xtinytoadx

Print Profile

new roller! updated, easier install

Simple to assemble, I just struggled to properly snap the ends into place. It might just be a me-problem, but the brim was very difficult to remove from the bed despite being totally cooled. Seems great otherwise, and I’ll try scaling it down and printing again because the standard size is too big and uncomfortable for my hands.

@PizzaBagels

the build is amazing and printed nicely

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Sturdy Modular Filament Spool Rack Fully Printable

Antiphrasis

58.9 k

31.3 k

GIF

Balisong aka Butterfly Knife new patterns and comb

iczfirz

85.3 k

21.8 k

GIF

Tri-Massage Roller (Fully printed)

SavageLau

206

Small Massage Roller (fully printed)

Bastel42