Bambu Lab spools winder SIMPLIFIED !

Search models, users, collections, and posts

B-Lab 3D

3D Printer>3D Printer Accessories

IP Report

Print Profile(11)

All

P1P

P1S

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

A1 mini

0.2mm layer, 2 walls, 15% infill

Designer

5.6 h

1 plate

4.7(824)

0.2mm layer, 3 walls, 25% infill

Designer

2 h

1 plate

4.7(655)

0.2mm layer, 3 walls, 25% infill

2.6 h

1 plate

4.6(116)

Moved to two plates sized for A1 mini

7.4 h

2 plates

4.6(45)

Click to see more

Open in Bambu Studio

Boost

3361

9182

2160

445

14.6 k

11.3 k

Released

Description

Hi, I needed to bring some filament onto AMS compatible spools, I've seen excellent projects around but too complex and expensive, I don't want to waste filament, time and money buying bearings, screws or anything else.

Simplifying as much as possible and without needing anything else apart from a printer, I designed this. Simplicity is fundamental for me! you can use the crank, or a screwdriver on the removable pin.

WARNING: for the unwinding spool I use an open filament dryer, otherwise print the parts 2 times to have a complete set

If you are interested feel free to bring updates, I left

consider this alternative with AMS Lite: AMS Lite Spool Winder by B-Lab 3D - MakerWorld

HAPPY PRINTING EVERYONE :D

bambu

spool

winder

Comment & Rating (2160)

@soltharix

Attempted with PETG-CF and everything seemed to come out OK, but upon fastening the bar together the male side broke off inside the female before I got anywhere close to it being finished. I was thinking PETG-CF would be a little tougher than just standard PETG but I could be wrong. Going to reprint just the male bar again but with more infill and a different pattern to test.

The designer has replied

@B_lab

Hello, as you mentioned, CF has superior strength, but as I've found in my other projects, its lack of smoothness causes a lot of friction between parts, so the design tolerances would need to be re-evaluated

Show original

@soltharix

Replying to @B_lab :

I think you're correct...it didn't seem like a smooth turn into the hole of the receiver so i'll try with just basic PETG on my next run and let you know!

@B_lab

Replying to @soltharix :

I look forward to hearing from you thank you for your interest 👏

Show original

@shopbitcoinaus

Print Profile

0.2mm layer, 3 walls, 25% infill

Thank you for the easy print. - Minimal material. - Minimal Components. - Option of manual or automated rotaton. - Threads worked without issue; sufficient surface-surface contact to maintain a good fit.

(Edited)

The profile uploader has replied

@B_lab

your support is very important to me, thank you for sharing your experience, happy printing 🌈

Show original

@JM84.ie

Print Profile

0.2mm layer, 2 walls, 15% infill

printed 2 copies, printed well with PLA basic. used for unspooling Amazon PETG filament to a Bamboo lab spool to fit in AMS.

The profile uploader has replied

@B_lab

Thank you for supporting this model, I hope you find it useful, happy printing 🌈

Show original

@Xderbe

Print Profile

0.2mm layer, 2 walls, 15% infill

Works perfectly and flawlessly I designed adapters for the new Sunlu spools for this purpose Simply superb You can find the adapters on my profile :-)

Show original

@ayip75

Thanks for the spool adapter.

@Xderbe

Replying to @ayip75 :

With pleasure, have fun and best of luck

Show original

@user_1986234617

where is this adapter? 🤞🏻

@pete12cf

am I missing something? I printed this 3 times with different filaments and different strengths. the male and female Jam each time and the male snaps. even trying to go in and out a little at a time. how were folks successful with this? I tried with and without supports as well.

@user_552287965

idem

Show original

@lrcustoms

Print Profile

0.2mm layer, 3 walls, 25% infill

Work properly. Printed on PETG, easy and simply to use.

The profile uploader has replied

@B_lab

Thank you for your support, I'm truly glad everything is in place, happy printing ☃️

(Edited)

Show original

@user_2931531279

What am I doing wrong? I printed the trays, but the original Bambu filament is too small – I can't tighten it, so it wobbles around.

@user_552287965

idem

Show original

@user_2917553969

Print Profile

0.2mm layer, 3 walls, 25% infill

The model is good, sadly tronxy spool is narrower

The profile uploader has replied

@B_lab

if possible can you upload the model for everyone happy printing 🌈

Show original

@user_2917553969

for anothers spools fit so good

@kobaX_

Print Profile

0.2mm layer, 3 walls, 25% infill

Works great

The profile uploader has replied

@B_lab

Thank you for your beautiful result, happy printing 🚀

Show original

@vittorio.iadaro

Print Profile

0.2mm layer, 3 walls, 25% infill

perfect

The profile uploader has replied

@B_lab

Thank you 🤩, happy printing ✅

(Edited)

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.