ok so i know that i am never on anymore… i have a lot of school and filming so i really busy but i have a problem… the plate part of the filament poop shoot thing broke! but it was still screwed just the other side fell and the thing that holds it there looks broken… i got it to stay put kinda by tightening the screw, but when i tighten it the part that slides gets stuck… i think i have it tight enough to stay but loose enough for the other to not get stuck… do i need to replace a part? you cant really tell but i hope it is an easy fix with no replacements

hey guys … so one i got the printet working yayyy… but i just fou d out i am going to disney AHHHH! so i need ideas for things to print… let me know any good prints

OK now I haven’t been on in a while and it’s been really busy but something really bad happened so a bit ago I ran out of my oil and so we were trying to buy some oil but we actually bought grease and then I found out I actually haven’t used grease yet and I hadn’t been oiling a spot that I needed to, but we’re like it’s fine so we started to print and it caused a ball of death. I thought it was OK so I started pulling out all the filament and this one was a bad one. It went behind the nozzle and everything and I was using the nozzle heating to heat it up melt it but then all of a sudden it started not heating up as much anymore like it would take a lot large heat up and then It just really started to stop like it went to like 0°. It would go up to six then it would go back to zero and then it started going to negative and now it’s not heating up at all I think that’s something. happened… I don’t know if something got pulled or if it’s like a malfunction and I’m just hoping that’s not gonna be so that needs to be replaced cause I don’t know if I even can like replace everything do y’all think that’s still OK is there anyway that can fix this or am I just gonna have to pay a lot of money to get it fixed?

hey guys, I know I haven’t done anything in a while. I’ve been very busy trying to grab my business on other platforms has been really time-consuming and I need Ideas on things like to film about they even sell, especially ones that I don’t have to pay like a membership or something for at least not at this point maybe in the future I’ll start paying for memberships but right now we’re not at that point if y’all have any ideas and also maybe some ideas soon on things to design

I AM BACK! sorry i havent been active in a while… i have been really busy but i will try to post more models and be more axtive… but question.. i got a new build plate from amazon. a double sided effect one. but this one is different. it doesnt have the roundish end that helps put the plate in correctly,and that also is the part for nozzel calibrations and i dont know if i can use it because i tried once and it receved error… do you think i can still use it… i only got it yesterday

Question ok so i have been seeing all over the internet these K POP DEMON HUNTER collapsable Rumi swords but i can not find a model to print it anywhere and i really need one so if someone is working on one or knows where i can print it let me know

100!!! WE JUST HIT 100!!!!! THANK YOU TO ALL THAT DO AND I AM SO SORRY I HAVENT BEEN VERY ACTIVE I HAVE BEEN VERY BUSY BUT I WILL TRY TO DO MORE SOON

ONE FOR FOLLOWER BEFORE I HIT 100 CAN WE HIT IT BEFORE SATERDAY

this is on one of my walls in my 3d printing room hahaha🤪😂😂😂😂

sorry if i have not been active really and havinf been posting model i have been really busy but i may be able to start posting some soon and thank you for ALMOST 100 FOLLOWERS WE ARE AT 94 and I THINK WE CAN HIT 100 BY THE END OF THIS WEEK OR NEXT WEEK AND THANK YOU TO ALL THAT DO

am i the only one with this problem so i will be printing and it finishes and the touch screan wont turm on and then i have to turn it off and back on agian

you know what someone should make andi am calling out the gods of …dummy 13 for………kpop demon hunter dummy 13! wouldnt that be cool you could be a demon like saja boys or hunters like huntrex and i think it would be great so like all of yall that do dummy 13 stuff pleaseee make thess

THEY ARE HERE AND THEY ARE SOOO COOL AND I CANT WAIT TO START PRINTING I THINK I WILL NOW PROBABLY SOME #K-POP DEMON HUNTERS stuff so let me know about any good ones and can someoen find or design collapsible rumi sword i have been looking but i cant find any or at least not any that are free

THERE HERE I AM ABOUT TO DO A UNBOXING SO CHECK IT OUT btw it my dog probably will be loud because he is in the 3d printing room for s fee days

Farewell, My Faithful Nozzle: A Tragic Tale of TPU and Tears 😭🔩 Well, MakerWorld, it’s time to retire my poor, battered nozzle. This brave little guy has seen it all: blobs of death, clogs that laughed in my face, and enough scraping to star in a horror flick. It’s been through so much wear and tear, it deserves a medal—or at least a tiny 3D-printed tombstone. ⚰️ Now, I’m trying to print TPU (and even PLA!), but it’s a disaster. The printer’s like, “Filament? What filament?” It thinks there’s gunk on the nozzle, or maybe it’s just confused, who knows? It’ll chug through a whole print, then stop extruding one-sixth of the way in, leaving me with a sad, half-baked model. 😿 I’ve tried cleaning it, but there’s this waxy, powdery junk inside that smells like burning plastic and regret. I cranked up the heat once, hoping to fix it, and—surprise!—a melted, waxy liquid oozed out, stinking like the grim reaper’s candle collection. 🕯️💀 So, MakerWorld, should I send this nozzle to its eternal rest and grab a new one? Drop your wisdom (or condolences) below! 🪦🛠️ sorry the camera was out of focuse

yay I. hit over 80 followers again thank you to all but I dont think I can shout you all out so just look at who they are on my profile and lets try to hit 100 before the end of the month if possible thanks

yay i got to 1,000 points! thank you and thanks to the person who did the last boosts @f34r i think so thankssssssd

has anyone seen my new model I want it to get a lot of prints so my

ITS HERE! YAY and the ones who guessed correctly will get a follow a like and a share so let me know if you guessed right and some guessed almost right if you said pencil then it does count so let me know

IT IS HERE!!!!!!!!!!!!!!!!! These are the pencil earrings and they will be great gifts for teachers or cool to wear on the first day or you can make it a neclace or keychain but it will be great gift for all and i hope yall have a blessed day.