Printer: ENDER 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament material: PLA Blanck and White Print speed: 55mm / s Nozzle: 0.4

Settings and manufacturing instructions

Printer: ENDER 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament material: PLA Nozzle: 0.4

Printing Instructions: Material: PLA or PETG. Nozzle: 0.4mm. Layer Height: 0.2mm. Color Change: Set a filament swap at the top layers to achieve the iconic bicolor finish shown in the photos.

Recommended Settings: Layer Height: 0.2 mm Infill: 15% Wall/Front Face: Print with translucent filament on the front face and edges for the best LED diffusion effect. Lighting: Use Red and Blue LEDs to achieve the Instagram gradient look.

PRINT SETTINGS: Layer Height: 0.2 mm. Infill: 15% - 20%. Wall Count: 3 for better light containment. Material: Red PLA for the body and Translucent White for the diffuser face. Supports: No supports needed if printed flat.

Material: PLA, PETG or ABS (Black Red for body / White or Clear for diffuser). Infill: 10% to 15% Layer Height: 0.2mm (Standard) or 0.28mm (Draft/Fast). Pro Tip: Use at least 3 perimeters (walls) to prevent light bleeding through the sides.

Material: PLA (Black for the case / White for the 'X' diffuser). Layer Height: 0.2mm for a smooth, premium finish. Infill: 15% (to keep it sturdy). Walls: 3 perimeters (prevents light from leaking through the black plastic). Tip: Use a high-density LED strip for the most uniform "Green Glow" effect.

3D printing settings Material: PLA, ABS or PETG. Layer Height: 0.2mm. Infill: 15% to 20%. Walls/Perimeters: 3 Supports: NO SUPPORTS NEEDED. (Print flat). Tip: Ensure your retraction is tuned for a clean finish on the latch/hinge area.

Material: PLA, ABS or PETG Layer Height: 0.2mm. Infill: 20% (Grid or Gyroid). Walls/Perimeters: 3 for hinge and latch durability. Magnet Slot: Designed for a 10mm x 1mm disc magnet. Supports: NO SUPPORTS NEEDED.

Material: PLA, PETG or ABS. Layer Height: 0.2mm or 0.24mm (for speed). Infill: 20% (Gyroid recommended for strength). Walls/Perimeters: 3. Magnet Slot: Fits 10mm x 1mm disc magnets. Supports: NO SUPPORTS NEEDED.

Material: PLA, PETG or ABS. Layer Height: 0.2mm. Infill: 15% to 20%. Walls/Perimeters: 3 for long-lasting hinges. Supports: NO SUPPORTS NEEDED. (Print flat).

Material: PLA, ABS OR PETG. Layer Height: 0.2mm. Infill: 20%. Walls/Perimeters: 3 for extra strength. Supports: NO SUPPORTS NEEDED.

Material: PLA, ABS OR PETG. Layer Height: 0.2mm. Infill: 20%. Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED.

Material: PLA, ABS or PETG. Layer Height: 0.2mm. Infill: 15% to 20%. Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED. Note: Ensure good bed adhesion.

Material: PLA, ABS OR PETG. Layer Height: 0.2mm. Infill: 15%. Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED. Note: Prints fast and uses very little material.

Material: PLA or PETG. Layer Height: 0.2mm. Infill: 20% (For structural rigidity). Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED. Tip: Print in different colors to separate "Charged" from "Dead" batteries.

Material: PLA or PETG. Layer Height: 0.2mm. Infill: 20% (For structural rigidity). Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED.

Material: PLA, ABS OR PETG. Layer Height: 0.2mm or 0.24mm. Infill: 15% to 20%. Walls/Perimeters: 3. Supports: NO SUPPORTS NEEDED.

Recommended Material: PETG (best choice for wet environments and long-term durability) Layer Height: 0.24 mm – 0.28 mm (faster printing without compromising strength) Infill: 20% (Grid or Gyroid) Walls / Perimeters: 3–4 walls (critical for edge strength and load capacity) Supports: ❌ Not required (print flat on the build plate) Mounting Tips: – Heavy-duty waterproof double-sided tape for clean installation – Or screw mounting for maximum load support