Bambu X1/P1 Lead Screw Shield No Support needed
Remixed by
Copyright Claim
Bambu X1/P1 Lead Screw Shield No Support needed
Remixed by
Boost
53
122
32
Print Profile(3)
10x3mm right side 10x3mm 0.2mm layer, 3 walls, 25% infill
Designer
1.6 h
1 plate
Left side update 0.2mm layer, 2 walls, 15% infill
Designer
1.2 h
1 plate
10x3mm Left side 0.2mm layer, 3 walls, 25% infill
Designer
1.5 h
1 plate
Boost
53
122
32
0
282
150
Released
Description
No support is needed, I modified the model that way, increased the size of the magnet holder, the original one was too small. I made a model for 6x3mm, 8x3mm, and 10x3mm magnets, I recommend the 10mm magnet, itholdswell!
Update:
Left side cover, updated I also cut off the corner a little to make it the same! The update version for the print profiles!
Comment & Rating (32)
All
Print Profile
10x3mm right side 10x3mm 0.2mm layer, 3 walls, 25% infill
Die Rechte passt zum X1C aber die linke passt garnicht! In Beschreibung war für X1C auch.... falsch. Sonst schöne und gute Model.
The designer has replied
0
Reply
Senken Sie den Tisch komplett ab und versuchen Sie es so :D Sonst passt es nicht...
0
Reply
Heute habe ich probiert. Ich konnte auf den Stelle setzen. Beim erste druck Anfang hat den Drucker gemeldet, eine Z Achse ist Fehlerhaftig ist. Also ich habe die linke entfernt. Schade. So hab ich nur auf die rechte Seite. Nicht desto trotz danke dir die Lösungsvorschlag!
0
Reply
Replying to @Jocika
Ich denke, es war fehl am Platz, die Drucker sind die gleichen und man kann die Bilder sehen, es ist für alle gut :)
0
Reply
printed well in PETG but the updated left side doesn't fit a 10x3mm magnet. it fits a 6x3. see it next to the right side here. pretty sad I wasted that print 😞
The designer has replied
0
Reply
fixed and sorry :) Put a smaller magnet in it and you don't have to reprint :)
1
Reply
thanks! hopefully I can find one that size (and it'll be strong enough)
0
Reply
Print Profile
10x3mm right side 10x3mm 0.2mm layer, 3 walls, 25% infill
Great print, glue drying for magnets, the. install
0
Reply
Print Profile
10x3mm right side 10x3mm 0.2mm layer, 3 walls, 25% infill
Thank you.
0
Reply
@Poli27 Can you tell me what kind of ledge is at the bottom of the floor? Do you have a link for that?
1
Reply
I'd also like to know. I believe it's the bottom section made by "Malkus" in his lead screw cover model, but I'm not positive. If it still fits with the update for the left side, that would be great.
0
Reply
https://makerworld.com/en/models/63077#profileId-74896
0
Reply
What else do you have in your printer? The red, yellow, and black box? I'm interested... :-)
The designer has replied
0
Reply
Bento box
0
Reply
Print Profile
10x3mm right side 10x3mm 0.2mm layer, 3 walls, 25% infill
doesn't stay in place at the bottom of my P1S and interferes with bed movement
The designer has replied
0
Reply
User error, It's been flawless for me for months, is that why you put a magnet in it? :D
0
Reply
Print Profile
Left side update 0.2mm layer, 2 walls, 15% infill
doesn't fit on my P1S. bottom half loose and interferes with bed movement.
The designer has replied
0
Reply
It's been flawless for me for months, is that why you put a magnet in it? :D
0
Reply
what are those 3 colored boxes stacked inside your printer in the rear right corner?
The designer has replied
0
Reply
Bento box.
0
Reply
Where is the bottom middle piece? Can't see to find it in a print profile or the raw model files...
0
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-Noncommercial
© 2024 MakerWorld