Flexi Bearded Dragon

Flexi Bearded Dragon

Boost
2825
5115
541

Print Profile(5)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
4.1 h
1 plate
4.8(289)

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
4.6 h
1 plate
4.9(63)

A1 Mini - .28mm layers - Gyroid 10%
A1 Mini - .28mm layers - Gyroid 10%
3.2 h
1 plate
4.6(18)

0.6mm nozzle, 0.3mm layer, 2 walls, 5% infill
0.6mm nozzle, 0.3mm layer, 2 walls, 5% infill
2.5 h
1 plate
5.0(2)
Click to see more

Open in Bambu Studio
Boost
2825
5115
541
569
6.1 k
3.1 k
Released

Description

Realistic flexi bearded dragon - 100% print in place with no brim or support needed, easy to print & quick multi-color print

 

The pocket bearded dragon is also available to all subscribers along with commercial licences for all designs

 

Both designs are silk compatible simply follow your filament print specifications

 

Have fun printing and don't forget to share your prints 

Comment & Rating (541)

Please fill in your opinion
(0/5000)

Boosted
so realistic
The designer has replied
49
Reply
This is your real pet dragon on your printer? XD
3
Reply
Boosted
Replying to @FilliFuu :
yup 😂
3
Reply
cool I have same b dragon 😃
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
I have tried to print this on 9 different occasions and either the tail or one of the legs has poor adhesion to the bed. I have tried multiple and new filaments including some from Bambu, cleaning the bed with Dawn soap, changed the bed temp from 55, 60 and 65, changed the z-hop, turned off the fans and reduced the speed by 50%. The printer is only 4 weeks old so I did not clean the lead screws. I gave up trying to print it and switched to Articuated Snakes which printed fine on the first try.
The designer has replied
12
Reply
I'm sorry to hear that but it sounds like a problem your end - When cleaning your plate, use dish wash soap with hot water and scrub with a sponge with the green scourer and use the course side, scrub in all directions for at least 5 minutes, rinse thoroughly then air dry the plate vertically. And if all else fails then slow the print speed down
1
Reply
Replying to @FilliFuu :
I have tried both of those. The only thing I can think of is a brim. I have printed 3 other prints fine with no adhesion issues using the same settings. Not sure what it is about this one. I may try to turn the bed temp up to 70 seeing how it is the middle of winter and cold where I am from
(Edited)
1
Reply
Replying to @tkimb :
It can depend on the surface area, theres lots of small parts on this flexi making it more difficult
1
Reply
currently 30 mins from a finish, the tail is moving and not getting a good lay. still new to printing but I’m assuming maybe my bed didn’t calibrate correctly? A1 bambu
The designer has replied
1
Reply
Adhesion problem, your print came loose from the bed. You need to clean your print bed, you can also enable the z hop setting if you have further issues down the line.
0
Reply
didn’t think it was a cleaning issue since I cleaned it right before. I heard best ways of cleaning is with soap and water or glass cleaner? I’ve done both, but today I did glass cleaner.
0
Reply
Replying to @roblo :
you might need to clean the lead screws.
0
Reply
Printed out great no supports. I did not simplify the model like the slicer suggested. Wood filled PLA and black PLA+ for the eyes. P1s combo printer.
3
Reply
Which specific PLA wood filament do you use
Show original
0
Reply
Replying to @BoxerBiene :
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
perfect print. he looks so real!!! ty
2
Reply
What plastic did you use to get this color? It looks great and so real.
(Edited)
0
Reply
Overture PLA Professional BROWN
0
Reply
Boosted
Great print thank you. Following for more.
The designer has replied
1
Reply
And theres much more coming soon ) thanks
0
Reply
sadly ours always goes bad after the first few layers and seems to kick off some of the central pieces, the wings on the lower layers start turning upwards also, I’ve tried shrinking it, rotating it, any advice would be appreciated!
0
Reply
same here 🥲
0
Reply
If you're prints are lifting or warping, you might want to try lowering the bed temperature.
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
perfectly designed. kids love it!
The designer has replied
1
Reply
Cool color, which filament is it?
0
Reply
He doesn’t even know.
The designer has replied
0
Reply
XD
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
nice one thanks
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Get Commercial License