Pringles Tray by SaVo3D

SaVo3D

Household>Other House Models

Print Profile(6)

All

P1P

P1S

X1 Carbon

X1E

PLA

Designer

1 h

1 plate

4.9(28)

updated version, shorter, smaller dia., thicker walls

Designer

1.2 h

1 plate

4.6(12)

PETG

Designer

1.1 h

1 plate

4.3(3)

224mm long for the dutchman

Designer

1.1 h

1 plate

5.0(1)

Click to see more

Boost

203

334

123

240

265

Released

Description

This is my version of a pringles tray!

Shove the tray into the can and pull out the tray with the pringles chips.

29.12.2023:

I uploaded a updated version. This version is shorter in length, so you can leave the tray inside and close the lid. Also i decreased the diameter by a few mm and increased the wall thickness.

Before printing, make sure your build plate is clean and apply some adhesive. Wash the build plate with oil free soap and wipe it off with some paper towels. For best build plate adhesion, i use a strong hairspray. Apply a thin, even coat of it. I repeat the cleaning and reapplying of hairspray every 5-6 prints.

pringles

tray

Comment & Rating (123)

@copymaster

Print Profile

updated version, shorter, smaller dia., thicker walls

very nice design. Thanks

The designer has replied

@SaVo3D

Thank you kindly!

@copymaster

Replying to @SaVo3D :

Just found out that the small version did not fit the (Dutch) Pringles tray. It is still too long.

@SaVo3D

Replying to @copymaster :

Can you give me the measurements and a photo of your pringles can?

@p666buc

Print Profile

PLA

printed great with PETG

The designer has replied

@SaVo3D

Thank you kindly! What is that pattern on the bottom face? You did not use my printprofile, right?

@p666buc

Replying to @SaVo3D :

I used octagram top surface pattern, I only use it when using transparent filament.

(Edited)

@SaVo3D

Replying to @p666buc :

Interesting pattern :-)

@joasolvang

Print Profile

PLA

works like a charm. No more hands stuck in tube :D

(Edited)

The designer has replied

@SaVo3D

thank you kindly

@hookuum

Print Profile

updated version, shorter, smaller dia., thicker walls

Fantastic idea. I did have to scale the length 10% to work. thank you for sharing

The designer has replied

@SaVo3D

Thank you kindly. From where do you come from? I am located in germany. Besides the Netherlands, there were no reports about size issues.

@copymaster

Print Profile

224mm long for the dutchman

Thank you many times. Reprinted for your effort. I have two now. Sand over it and keep going.

The designer has replied

@SaVo3D

Thank you kindly!

@Flori_

Print Profile

PLA

printed perfectly

The designer has replied

@SaVo3D

Thank you kindly! Have a look at the "updated version" it si shorter so you can leave it inside the can and close the lid.

@Marcel_X

Great design! Maybe make a shorter version, so it can be kept inside the canister? Ah, well... Once you pop, you cannot stop :-)

The designer has replied

@SaVo3D

Good idea, i will do it as soon i have time for it but it will take some days. Meanwhile you can simply scale it down in one direction in bambu studio. Yes, pringles get you addicted 😀

(Edited)

@dronography.ire

Print Profile

PETG

wals a bit weak :)

The designer has replied

@SaVo3D

what exactly is the problem? Did you print from my printprofile?

@dronography.ire

Replying to @SaVo3D :

yes from profile... ive propably squeezed it too much.. don't know

(Edited)

@SaVo3D

Replying to @dronography.ire :

Why did you squeeze it? Is the diameter too big? I will upload a updated version, that is smaller in length, so you can leave it inside the can. Plus i will reduce the diameter by a little bit. Solution? 😊