Desk Cable Management Holder / Organizer with Screw V2.0 by MBRS

MBRS

Household>Office

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

V2.0 - 0.2mm layer, 3 walls, 13% infill

Designer

33 min

1 plate

4.4(28)

LONG CLAMP V2.0 - 0.2mm layer, 3 walls, 13% infill

Designer

35 min

1 plate

4.1(11)

0.2mm layer, 3 walls, 13% infill

40 min

1 plate

4.5(2)

0.2mm layer, 3 walls, 13% infill

38 min

1 plate

3.8(4)

Boost

232

394

496

Released

Description

I needed a cable organizer for my desk, without glue, adhesives and making a hole in it. Designed this very simple one, with a screw to fix it tight and 3 holes for most cables. You are free to change the dimensions to suit your needs.

V2.0 VERSION: Screw scaled to 97.5% as reviews showed a better fit. Also added knurling.

I also made a bigger vise version for thick desks.

If you need this to tidy up passing cables you should check out my other model made for that purpose

Comment & Rating (68)

@riceball

Print Profile

V2.0 - 0.2mm layer, 3 walls, 13% infill

Great. Not sure how easily the cable will fall out of the hole when using though. Feels like will fall out easily. Edit: I added a rubber band to prevent thin cables from falling out. Perfect. :)

(Edited)

The designer has replied

@AMB.Tech

What filament is that? In any case the cut in the hole is big because i noticed some cables wouldn't fit otherwise. I have thought of uploading many versions each with different holes for cables but it would be too messy. Maybe I can write all the dimensions in the description. Thanks for the review !

@riceball

Replying to @AMB.Tech :

It's the Bambu PLA Basic Black. Yea the hole makes sense, but perhaps the design could be tweaked for it to be a bit harder to put in and take out. Maybe with a bend or notch or something.

@Heman

Print Profile

LONG CLAMP 0.2mm layer, 3 walls, 13% infill

Print is quick. Screw scaled to 97% was perfect fit for me. I’d maybe add knurling to the knob.

The designer has replied

@AMB.Tech

thanks for the feedback! as soon as I have some time I’ll update with the scaled x y screw on 97% and knurling

(Edited)

@nikolay79

Print Profile

0.2mm layer, 3 walls, 13% infill

very useful. thanks for sharing!

@gdmodels

Print Profile

0.2mm layer, 3 walls, 13% infill

the screw is too tight a this setting. broke off the first use.

The designer has replied

@AMB.Tech

I see, I may just have been lucky with mine. I’ll make an updated version with a loose fit for the screw. would you like to see anything else in a new version like holes for bigger cables and such?

(Edited)

@gdmodels

Nice print. I used the 0.2mm layer, 3 walls, 13% infill file. The screw is tight and broke with the first print. I scaled the screw to 98% and it's still a tight fit but didn't break this time.

@joeythatoneguy

Print Profile

V2.0 - 0.2mm layer, 3 walls, 13% infill

came out great! It would be nice to have a longer screw for desks that aren't so thick. I had to add some foam tape to make up the difference just to keep it on my desk 😂

@jsimages

Print Profile

V2.0 - 0.2mm layer, 3 walls, 13% infill

perfect 🤩

@nanshe23

Print Profile

0.2mm layer, 3 walls, 13% infill

Works fine for me. Printed with PLA Jayo Matte.

@FrogRan

screw broke almost immediately, and the lack of measures in the description is a very bad experience.

@botboy23

Print Profile

LONG CLAMP V2.0 - 0.2mm layer, 3 walls, 13% infill

Very strong and solid. In some cases may be overkill versus simple loops, but still not a lot of filament. Would like to see another version with longer screw.