Adaptable Sponge drip tray by FlorinV

FlorinV

Household>Other House Models

GIF

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

My choice

Designer

2.1 h

2 plates

4.8(80)

A1 Mini

Designer

2.4 h

2 plates

5.0(7)

Connect 2 or more trays

Designer

11 min

1 plate

5.0(2)

0.2mm layer, 2 walls, 10% infill

2 h

1 plate

Open in Bambu Studio

Boost

242

516

125

522

707

Released

Description

100mm x 80mm dimensions
Simple to print. Looks great in Marble PLA.
Optional adjustable screwing feet for over the sink lip positioning.
The interior is designed with 4 slopes combined to direct the water from all 4 corners to the middle dripping hole.
Front text “KEEP IT CLEAN” …. in case we forget :D
If you want a stronger voronoi grille, you can scale up only the Z axis for the voronoi grille. (non uniform scale)
Update 10.01.2024: I've added another profile with a small “connector”, in case you want more than one drip tray.
If you print 2 or more drip trays, you can print this small connector to hold them together.

Comment & Rating (125)

@Zerschmetterlin

Print Profile

My choice

Nice Idea, works great, thanks.

The designer has replied

@FlorinV

Thank you !!

@Zerschmetterlin

Replying to @FlorinV :

Wait a minute... I just realized you also designed the toothpick dispenser? Holy! You are a genius! I was really impressed with the toothpick thing (and I'm an engineer, I'm not easily impressed by anything)! Keep up the good work <3

(Edited)

@FlorinV

Replying to @Zerschmetterlin :

:)) … thank you! glad you like that also!! did you checked my bambu filament cutter? curios of your honest oppinion on that one! ( i had big hope for that, but it was not received so well… maybe i’m missing something …)

@AdVanceYourself

Print Profile

My choice

Great addition to the kitchen counter. a little small for my sponge so I may play with scaling at some point. I printed at ludicrous speed so ignore the text artifacting.

The designer has replied

@FlorinV

thank you! looks too good for that speed ! :)) beside size, you think it could be improved in other ways? i like it in my kitchen, but would love to be heavier…. i’m thinking maybe to increase the infill, but still will not be too heavy…

@AdVanceYourself

Replying to @FlorinV :

I was looking around as I also have one of those bristle scrubbers i'd love to put in a tray. Perhaps having some remixes with a tray to the side (and outlet for drainage) with a very slight angle to drain would be awesome. to hold one of these (https://www.ikea.com/us/en/p/videveckmal-dish-brush-with-soap-dispenser-bright-green-90556702/) . and perhaps a remix with it on both sizes to hold the drain stoppers.

(Edited)

@FlorinV

Replying to @AdVanceYourself :

Hi again, Thank you a lot for your ideas. I did add a small connector. Not exactly what you had in mind, but maybe it works for your and it was simple to add this. If you print 2 or more drip trays, you can print this small connector to hold them together. Please check the new profile with the connector.

@cammi187

Print Profile

My choice

modified it a little bit to fit more stuff onto it.

The designer has replied

@FlorinV

Nice! You could try and print two times the Voronoi Grille (one above the other) to make it more stronger for the bottle of soap :))

@cammi187

Replying to @FlorinV :

it bends a little bit but I am not concerned about it

(Edited)

@FlorinV

Replying to @cammi187 :

Hello again, I saw you use 2 drip trays. I did add a small connector. You can print this small connector to hold them together. Please check the new profile with the small connector. ( it's 11 minutes print, but I like it, because i hate to have them move around too much. If you try it and you scaled the drip trays, please scale the connector the same )

@herol

works well, the threads are a little tight

The designer has replied

@FlorinV

Wow.... i really like that color ! What filament is that ? Sorry about the threads, I wanted to not move after I set them, as you don't need them to be moved after initial setup. If you want them looser, You can scale the screws down non-uniformly to 99% or even 98%. (only X and Y axis, NOT Z ) Thank you for your review !

@herol

Replying to @FlorinV :

Yeah, it wasn't that much of a problem, the screws went in, just a little hard. The filament is Bambu PLA Basic Green (10500).