Miniatures Paint Brush Cleaning Pot

Miniatures Paint Brush Cleaning Pot

Boost
1315
3449
378

Print Profile(3)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.2mm layer, 3 walls, 5% infill
0.2mm layer, 3 walls, 5% infill
Designer
2.8 h
1 plate
4.9(248)

NO D20 - 0.2mm layer, 3 walls, 5% infill
NO D20 - 0.2mm layer, 3 walls, 5% infill
Designer
2.8 h
1 plate
5.0(65)

A1 Print Profile - 0.20mm, 5% infill
A1 Print Profile - 0.20mm, 5% infill
3 h
1 plate
5.0(1)

Open in Bambu Studio
Boost
1315
3449
378
401
2.6 k
1.9 k
Released

Description

 

Citadel paint pot holder add-on now available too!

 

 

Here is a paint brush cleaning pot for painting miniatures

Features 

Rest over top for current brush

Three brush holder at the rear

Grooves on the bottom and sides for cleaning brushes

Grooves towards top to get he point back on the brush.

 

Boost Me (for free)

All of my models are free to be used commercially so why not boost me to show support?

 

Comment & Rating (378)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 3 walls, 5% infill
amazing design. exactly what I needed and then some
The designer has replied
2
Reply
thank you so much for the feedback
0
Reply
@AsAbove_SoBelow What is the brush holder behind the cup?
3
Reply
Replying to @TachyPrints :
I'm also curious about these 2 brush holders.
0
Reply
Boosted
Awesome quick print! Anything special that needs done to sell commercially? I would like to put them in my online and physical stores. I might not sell a lot locally but I think they should sell well in my gaming groups!
The designer has replied
2
Reply
Thank you for the feedback, looks like it came out well. No nothing needs doing, feel free to sell them however.
10
Reply
Print Profile
0.2mm layer, 3 walls, 5% infill
Had a print failure (not profile related, honestly not sure why it got off kilter), but was towards the top, so was able to slice it and re-print just the top and glue it together. Tried it in a transparent to see how it would turn out, and really like it!
1
Reply
Looks dope!
0
Reply
Print Profile
0.2mm layer, 3 walls, 5% infill
perfect design for a gift to my wife. side surface and bottom surface different textures for cleaning the paint from the bristles. she usually uses two to three brushes at a time and there are three vertical spots for brushes and the horizontal rest at the top. really a clever design. I used PLA, I’m new to this and I feel that might have been a mistake. I’m waiting to hear of a puddle on her desk as a result of using PLA, hopefully I’m wrong 😱🤣
The designer has replied
0
Reply
I had water in mine for 3 days without any issue. hope it works out for you. increasing temperature or wall count should help
0
Reply
Replying to @TachyPrints :
thank you, that’s helpful advice!
0
Reply
this looks nice! I'm curious did you have any problems with water seeping out since printed PLA typically isn't watertight. did you do any postprocessing to make it water tight? I'm super lazy and typically leave my cleaning cup with the dirty water for days hehe
The designer has replied
3
Reply
I left mine with water in it for 24 hours with no issues
1
Reply
I see, good to know, thanks!
0
Reply
If you have issues with your prints holding water you can slightly overextrude them, like 101% and that will almost certainly make them watertight. When I print planters I usually overextrude them and do 4 top layers for some peace of mind.
(Edited)
0
Reply
Print Profile
0.2mm layer, 3 walls, 5% infill
sehr gut
The designer has replied
0
Reply
I'm glad to hear that, thank you for your feedback
Show original
0
Reply
Print Profile
0.2mm layer, 3 walls, 5% infill
very smooth and excellent design
1
Reply
Print Profile
0.2mm layer, 3 walls, 5% infill
Came out beautiful
The designer has replied
0
Reply
thank you for the rating. it looks great in that two tone filament!
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 5% infill
exactly what i needed, thank you!
0
Reply
Print Profile
A1 Print Profile - 0.20mm, 5% infill
The profile prints quite well (5 stars) and it looks beautiful, but printing in PLA did not make it leak proof. After an hour or so the water went in the material and leaked partially through. I will try to use a primer or something..
0
Reply