Mini version of the final bag clip by DieProfikeit

DieProfikeit

Household>Other House Models

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

Optimized to work on all machines, AMS optional

Designer

3.6 h

1 plate

4.8(202)

Optimized for A1 mini

Designer

3.7 h

1 plate

4.8(42)

With brim for better bed adhesion

3.2 h

1 plate

4.9(18)

A1 Mini, 1 Color, 0.2mm layer, 6 walls, 25% infill

4.4 h

2 plates

4.5(10)

Open in Bambu Studio

Boost

1734

4161

354

373

3.7 k

2.1 k

Released

Description

Boost Me (for free)

Leave me a boost if you like it!

Highly requested smaller version of my popular “The final coffee bean bag clip”.

For smaller bags or just cut the corner of bigger bags.

The cap is reworked to be more air tight, and the clip shrunken down as much as possible without making it harder to use.

The tenth of those you have seen probably, but implemented all the good stuff.
Snap lock lid, no printed threads, no screwing 3 turns, just snap it closed.
Easy to open and close, no fiddling and breaking your fingers.

The parts are print in place, no assembly or supports required.
Please dont move the clip parts or the hinge will not work.

Custom caps here:

Experimental TPU seals in the files.

Documentation (1)

Assembly Guide (1)

Manual.pdf

Bill of Materials

Bambu Filaments

Cocoa Brown

A00-N1-1.75-1000-SPLFREE

× 1

Black

A00-K0-1.75-1000-SPLFREE

× 1

Buy Now

Download BOM

Comment & Rating (354)

@DocRock

Aloha I have a question and as a noob I may be doing something wrong. I have a A1 with AMS and it printed amazingly; however on the bed side of the print the rotational joint fuzed and I was unable to open the clamp. Naturally the clamp broke. I'm sure it's a settings thing, I'm using Bambu official Black Matte PLA that has been flow calabrated. Any advise would be appreciated. Mahalo

The designer has replied

@DieProfikeit

Did you just use my print profile without any changes or one someone else made or changed something? Mine is tested thoroughly. It worked for thousands of people now without problems.

@Kmuniz2002

Replying to @DieProfikeit :

just curious, as i noticed you seem to instantly put blame on other people changing your print profile, why do you do this? if someone has an issue with the print profile you instantly assume their making changes to it just to give you a bad rating. if we post pictures about the print after it finished, it should be safe to assume its because of the print profile alone and not changes the person made. if the person made changes and it came out bad they shouldnt even be thinking about commenting under the post about it as their changes could have affected the print. just curious as to why you do that

(Edited)

@Kmuniz2002

Replying to @Kmuniz2002 :

also not thousands, you only have 1.2k prints on this model, thats not a valid reason for why hes having an issue with the print profile

@Kmuniz2002

Print Profile

Optimized to work on all machines, AMS optional

Support Issue:there’s no support at all? also how are we even supposed to assemble this? the parts don’t even flex nearly enough to put the part in. (this was printed off the app while I was at work, so this is the print profile itself) update: I just opened the file on pc, for the print profile creator, make sure you JOIN the 2 parts that are supposed to be print in place. not doing this ruined my print

The designer has replied

@DieProfikeit

Exactly, its print in place. The parts are positioned as they should be and it worked for hundreds of people without problem. If you dont mess with my print profile and dont use other peoples print profiles it needs no supports and no assembly. Please try again and revisit your rating.

@Eric.C

Good day, I encountered an issue where the slicer indicated floating parts, prompting me to enable supports! The print was a failure. I would have appreciated it if you had included this information in your description regarding Print in Place and support-free printing. Otherwise, a fantastic piece. 👍

Show original

@Kmuniz2002

Replying to @DieProfikeit :

i didnt mess with your print profile, i used the app (which should mean your print profile is 100% printable with no issues) and i added 2 because i would like to have 2 of these. BUT because you didnt MERGE the two pieces, it ended up breaking the model. if you fix the print profile and merge them nobody would have the same issue i have. like i said, your print profile isnt meant for the app, this is meant more for a slicer download and modify. it needs to be fixed if you want it to be compatible with the app with no possibiliy of issues. not revisiting the rating.

@jaq63.de

Print Profile

Optimized to work on all machines, AMS optional

Your coffee beans bag closure is a great part! I like the idea an good design. I added a TPU seal to my lid for complete sealing. both versions long and short are in use in our household now! Thanks for the design. Would love to upload my design, but that’s restricted.

@user_2472663001

Boosted

Hi, how did you add the sealing? I was thinking about an O-Ring to seal it tightly.

@jaq63.de

Replying to @user_2472663001 :

I printed a flat TPU disk a bit larger than the lid inner diameter, just 2 or 3 mm in diameter larger, about 3 mm thick I guess and than I added a negative of this disk to the right position in the lid to generate the space, that negative part was just a little bit bigger than my TPU disk.

@Sindorei

Print Profile

Optimized to work on all machines, AMS optional

Support Issue:no support

The designer has replied

@DieProfikeit

Its print in place, no assembly, there are no supports needed.

@Sindorei

I think this happens to the other user commented as well. I am not sure what to adjust to fix this, if I turn on support option, there is no support automatically assigned either

@Andy1

Did you use PLA? I've experienced similar issues, albeit with PETG

Show original

@gibsop1

Loving this! Tight to get closed since the clip covers the bag seam but better than a full sized one in my opinion. I might try to add a rubber grommet to the cap. Printed in Amazon Basics Gold PLA on my Ender 3v3 @ 0.12mm

(Edited)

@GeoffryFaulkner

Boosted

If you find something to make a good seal at the top let us know! I had the same issue with the clamp closing around a thicker bag. It might be nice to add a way to ratchet down the clamp, just in case the bag is too thick. Still a great print.

@lukelani

Boosted

Print Profile

Optimized to work on all machines, AMS optional

A very beautiful and compact closure, what I particularly appreciate is the lid, it's wonderful that it's not designed with a standard thread. Thank you for sharing with the community

The designer has replied

Show original

@DieProfikeit

Thank you!

Show original

@ppmr88

Boosted

Prints exceptionally well, allows for uniform scaling, and various materials are feasible. The clasp components must be moved together; otherwise, they will break. Printed partly on a Qidi Q1 Pro and a Bambu P1S. The red is Bambu PLA Matte, the blue is Qidi ASA, the silver is Sunlu PLA+, and the dark one, which appears almost black in the photos, is actually a camouflage green TEQStone PLA-CF. I would leave out the last two. Matte works, but ASA is the most stable. Thank you for this fantastic part. I will also try the “normal” and “micro” models. Edit: A TPU seal for the lid also fits perfectly, even scaled; sometimes I doubled the thickness. But I am unable to print the one for the neck like this.

(Edited)

The designer has replied

Show original

@DieProfikeit

It's curious how tolerances fluctuate so significantly despite using the same printer and filament calibration The lid has a 0.05 mm gap and is very airtight on mine

Show original

@Username32

Print Profile

Optimized to work on all machines, AMS optional

great print quality but the profile could be enhanced with brims. despite cleaning my bed with soap and IPA still had 2 failures.

The designer has replied

@DieProfikeit

Those are really large surface area parts. Should be no problem if your plate is ok. Thousands of people had no issue.

@Username32

Replying to @DieProfikeit :

hence why I still gave the 5 star. brims would just greatly reduce any potential issue noting I had the mid-hub fail twice.

@m1chlcz18

Print Profile

Optimized to work on all machines, AMS optional

Printed perfectly thanks

The designer has replied

@DieProfikeit

Nice color choice!

@m1chlcz18

Replying to @DieProfikeit :

Thanks! In case someone want to know, those are Bambu PLA Matte Latte Brown and PLA Matte Dark Brown

@lightblue

Boosted

With perfectly calibrated filament, an absolutely top result I should have ironed it though

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Print Profile(4)

Description

Documentation (1)

Bill of Materials

Comment & Rating (354)

License

Related Models

Simple bag clip

Simple bag clip (for snacks)

Hermetic Bag Clip

Crocodile bag clip remix