DRY PODS and SILICA TRAYS 500 grams

Remixed by

DRY PODS and SILICA TRAYS 500 grams

Remixed by
Boost
211
461
489

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
Designer
15 h
3 plates
4.9(203)

MULTI SLOTTED DESIGN 0.16mm layer, 2 walls, 15% infill
MULTI SLOTTED DESIGN 0.16mm layer, 2 walls, 15% infill
Designer
2.5 h
1 plate
4.7(14)

Boost
211
461
489
33
1.5 k
1.5 k
Released

Description

0,16 layer height rectilineair infill,

 

Complete setup for your AMS with almost 500 grams of silica…..

 

Use the cool plate for better adhesion or a brim with the textured plate, for me it worked fine without.

 

Hygrometer used: Thlevel Digitale minithermometer en hygrometer met lcd-scherm, 3 stuks, meet temperatuur en luchtvochtigheid, voor koelkast, aquarium, -50°C~+70°C (3 stuks B) : Amazon.nl: Huisdierbenodigdheden on AMAZON for €10,99

 

print 1 feeder button to test if they fit your AMS

 

Plate 1 :  has the 5 pods for the front of your ams, IF your hygrometer has different slots than the pod in plate 1 delete this pod in the left bar under the TAB objects and print the pod with different mounting slots from the second profile .

 

Plate 2 has:

  •  2 containers for using silica beads in the bottom of your ams instead of the standard CACL2 bags from bambu. Also funnels for easy filling the pod's of plate 1. 
  • 2 buttons for covering the sliders of the lid for closing your AMS and one for the button that is on front of the lid all without logo's 
  • 4 feeder saver's that should prevent wearing you're original feeders from filament rubbing 

Plate 3 are  : the 4 feeders plus the one button for opening your AMS but all with BAMBU logo's.

Comment & Rating (489)

Please fill in your opinion
(0/5000)

Could you make a version with perpendicular cutouts for the hygro/thermometer?
The designer has replied
1
Reply
I put it online I hope you like it ;)
(Edited)
0
Reply
Replying to @mkersjes :
Thanks, i will print it tomorrow :D
1
Reply
Replying to @faluethi108 :
i assume you did not download it yet , if so please download it again i made a small change to it and hope it works well now,
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
nice work! gives a nice look for Ams and works very well to reduce humidity with dissecant
(Edited)
The designer has replied
1
Reply
you could try to clean you're plate.
0
Reply
Replying to @mkersjes :
I Clean the plate with isopropylic alcool a tryed once to cleaned with hot water and soap! probably its a defected PEI plate or can be a ajust issue!
0
Reply
is it a original plate or from aliexpres? I have this plate from aliexpres and prints everytime great also have printed my boxes without a brim , but to be sure I added the comment: to use a brim if your adhesion is less. Was a bit surprised for the 3 star rating with the reason of bed adhesion ;) I am just now struggeling with a new "flake Pattern plate" with adhesion.
(Edited)
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
exactly what I needed just waiting on the hygrometer to arrive
The designer has replied
1
Reply
thanks, and glad you like it
0
Reply
Replying to @mkersjes :
apparently they changed the location of the clips at some point. It might be worth a second profile but I don't feel like doing to required reprint haha
0
Reply
Replying to @uberroot :
I do not completely understand are the clips other than both the positions in the second profile?
0
Reply
I created a funnel which makes it much easier to add desiccant to these holders! Check it out: makerworld.com/en/models/463978#profileId-372641
The designer has replied
1
Reply
I have already funnels with my model included. I do not know if your funnel works better ;) you could check it out
(Edited)
0
Reply
Replying to @mkersjes :
Ah, didn't see them! Oh well, good to have options.
0
Reply
Replying to @ClaytonMerkle :
nice work though, perhaps people will like them.
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
with the speed settings in the profile i got adhesion problems, after speed settings reset to stock and a small brim it works perfect
The designer has replied
1
Reply
thanks for the feedback , which material did you print it with?
0
Reply
Replying to @mkersjes :
Printed with GST3D PLA
(Edited)
1
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
came out great, printet 3x with hygrometer instead
The designer has replied
1
Reply
thanks for the feedback , May I ask what printer you have what filament and what settings you used?
0
Reply
i have P1P, printed with the profile provided by designer and with Bambu PLA Basic Jade White.
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
Excellent design. print failed midway through. I printed again with brim and it worked fine.
(Edited)
The designer has replied
1
Reply
thanks for the feedback , which plate did you use ?
(Edited)
0
Reply
Bambu textured PEI
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
It really was easy and fast
The designer has replied
1
Reply
thanks for the picture and feedback, I hope you enjoy the model please take a look at my other models
0
Reply
Print Profile
TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil
Great print!
The designer has replied
1
Reply
thanks , I hope you enjoy the model please take a look at my other models. thanks for the picture
0
Reply
brilliant fit thankyou
The designer has replied
1
Reply
thanks for the feedback and picture ( nice colour ) I hope you enjoy the model please take a look at my other models
0
Reply