DRY PODS and SILICA TRAYS 500 grams Remixed by mkersjes

Remixed by

mkersjes

3D Printer>3D Printer Parts

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil

Designer

15 h

3 plates

4.9(257)

MULTI SLOTTED DESIGN 0.16mm layer, 2 walls, 15% infill

Designer

2.5 h

1 plate

4.8(18)

0.2mm layer, 2 walls, 15% infill

Designer

2 h

1 plate

5.0(3)

0.16mm layer, 2 walls, 15% infill

Designer

2.6 h

1 plate

Boost

263

596

634

1.9 k

1.8 k

Released

Description

0,16 layer height rectilineair infill,

Complete setup for your AMS with almost 500 grams of silica…..

Use the cool plate for better adhesion or a brim with the textured plate, for me it worked fine without.

Hygrometer used: Thlevel Digitale minithermometer en hygrometer met lcd-scherm, 3 stuks, meet temperatuur en luchtvochtigheid, voor koelkast, aquarium, -50°C~+70°C (3 stuks B) : Amazon.nl: Huisdierbenodigdheden on AMAZON for €10,99

print 1 feeder button to test if they fit your AMS

Plate 1 : has the 5 pods for the front of your ams, IF your hygrometer has different slots than the pod in plate 1 delete this pod in the left bar under the TAB objects and print the pod with different mounting slots from the second profile .

Plate 2 has:

2 containers for using silica beads in the bottom of your ams instead of the standard CACL2 bags from bambu. Also funnels for easy filling the pod's of plate 1.
2 buttons for covering the sliders of the lid for closing your AMS and one for the button that is on front of the lid all without logo's
4 feeder saver's that should prevent wearing you're original feeders from filament rubbing

Plate 3 are : the 4 feeders plus the one button for opening your AMS but all with BAMBU logo's.

Comment & Rating (634)

@faluethi108

Could you make a version with perpendicular cutouts for the hygro/thermometer?

The designer has replied

@mkersjes

I put it online I hope you like it ;)

(Edited)

@faluethi108

Replying to @mkersjes :

Thanks, i will print it tomorrow :D

@mkersjes

Replying to @faluethi108 :

i assume you did not download it yet , if so please download it again i made a small change to it and hope it works well now,

@mk_3dprint

Boosted

Print Profile

TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil

nice work! gives a nice look for Ams and works very well to reduce humidity with dissecant

(Edited)

The designer has replied

@mkersjes

you could try to clean you're plate.

@mk_3dprint

Boosted

Replying to @mkersjes :

I Clean the plate with isopropylic alcool a tryed once to cleaned with hot water and soap! probably its a defected PEI plate or can be a ajust issue!

@mkersjes

is it a original plate or from aliexpres? I have this plate from aliexpres and prints everytime great also have printed my boxes without a brim , but to be sure I added the comment: to use a brim if your adhesion is less. Was a bit surprised for the 3 star rating with the reason of bed adhesion ;) I am just now struggeling with a new "flake Pattern plate" with adhesion.

(Edited)

@uberroot

Print Profile

TEXTURED PLATE WITH BRIM 0.16mm layer, 2 walls, 15% infil

exactly what I needed just waiting on the hygrometer to arrive

The designer has replied

@mkersjes

thanks, and glad you like it

@uberroot

Replying to @mkersjes :

apparently they changed the location of the clips at some point. It might be worth a second profile but I don't feel like doing to required reprint haha

@mkersjes

Replying to @uberroot :

I do not completely understand are the clips other than both the positions in the second profile?

@ClaytonMerkle

I created a funnel which makes it much easier to add desiccant to these holders! Check it out: makerworld.com/en/models/463978#profileId-372641

The designer has replied

@mkersjes

I have already funnels with my model included. I do not know if your funnel works better ;) you could check it out

(Edited)

@ClaytonMerkle

Replying to @mkersjes :

Ah, didn't see them! Oh well, good to have options.

@mkersjes

Replying to @ClaytonMerkle :

nice work though, perhaps people will like them.

@fuzzy.supernova

Boosted

It's a good print and my filament will definitely appreciate it. Takes a long time, but it's totally worth it. Parts were printed almost perfectly, except some minor problems on the back walls of bigger containers (see photos). I used a Bambu matte PLA charcoal black filament, to me it blends well with the color scheme of X1C and AMS. The only thing I think could be improved is an extra option for a hygrometer stand container. I think it is better to separate hygrometer and desiccant, so that you can add some desiccant to the upper half of a container, while leaving a hygrometer open and unobstructed, thus ensuring better humidity readings while still utilising the useful space. To me it would be a great way to further improve this remix. P.S.: By the way, don't buy/use any indicating desiccant as I did (orange or especially blue), because dyes added to it are toxic and potentially carcinogenic and you may expose yourself to inhaling/ingesting traces of them one way or another. Better buy clear silica and use hygrometers to judge its state, or at least be sure to use only small fraction of indicating beads. Basically, fresh desiccant will quickly lower and hold humidity below 10%. If desiccant fails to do that, it's time to regenerate it.

(Edited)

The designer has replied

@mkersjes

I have added a print profile to the model which contains the model with a whole in it. thanks for the feedback and pictures. I hope you enjoy the model please take a look at my other models

(Edited)