Poop Chute Tray with hidden handle+Lid by cm3dshop.de

cm3dshop.de

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

0.16mm layer, 3 walls, 15% infill

Designer

17.7 h

3 plates

4.7(228)

Poop Chute with No AMS

13.5 h

3 plates

4.1(16)

0.6mm nozzle, 0.3mm layer, 2 walls, 15% infill

16.7 h

3 plates

Boost

714

1401

364

3 k

Released

Description

Poop Chute with Tray and hidden Handle

Easy acess to the Poop with a pull out tray (if you got low space behind and besides the printer)

stays in place with 5 round Magnets (attached to the printer) d=6mm ; thickness 4mm (3mm will also work when not pushed all the way in)

tray can be hold closed with 4 magnets (Attention at the polarity!) …just optional

hidden handle with Bambu Logo for pull out the tray : flat with front when closed ; for opening push the top part in and then pull at the lower part…very simple and easy…fully printed

optional Lid for "clean design"

Added a version for Users with a 40mm Stone plate under the printer.. So there is additional space for the Poop. ;)

https://makerworld.com/en/models/79531#profileId-84152

At All it is a bit over engineered … but…does it really matter?! ;)

Just let me know in comments when you have suggestions for improvement.

ATTENTION: the print profile uses the PETG/PLA trick to get a super smooth interface between the Tray and the supports!

Comment & Rating (364)

@marcelcountry

Print Profile

0.16mm layer, 3 walls, 15% infill

Printed in PETG without supports, really functional and cute

(Edited)

The designer has replied

@cm3dshop.de

nice color mix! ;)

(Edited)

@ASackOPotatoes

Dang now i'm wishing i did my lid in another color.

@TLadd

So only PETG material used here?

@jfutey

It is a simple and efficient design, however, ultimately the waste filament tends to clog the chute well before the generously sized hopper ever fills up. When the poops drop in the hopper, they pile up right at the chute exit and then the backup begins. When the chute is blocked, the filaments then begin to clog inside the printer and then any long overnight AMS print will end up getting paused. If there was a way to make the waste drop in the hopper more evenly it would be a huge improvement.

The designer has replied

@cm3dshop.de

will work on it at Version 2! Unfortunately it is impossible to change the dimension of the printer / the outlets and the area they are located. So the higher the poop box is, the lower must be the angle of the chute. For Version 2 i will try a litte space, where you can add a small piece of plastic sheet (e.g. the plastic folders from school) ...this is hopefully more "slippery" and the poop will slide more to the front.

@fran.whelan60

try spraying the chute with WD40

@Jailbreaker07

Replying to @cm3dshop.de :

I put a smooth foil in the shaft, let's test it... but it slips better...

@starkeeper

I just printed the first plate. It looks good but is unusable. The support which covers almost the whole bottom of the tray is not removable. I assume this should probably be printed with special support filament or some kind of dissolvable filament? In Bambu Studio I can see there is one layer "Support interface" which covers the complete tray bottom (without any gaps). I tried to remove it with a sharp knife, but no chance.

The designer has replied

@starkeeper

Okay, I found my problem. The trick which was used here is that PLA does not adhere to PETG and vice versa. So if you print the model with PLA you must use PETG as interface layer for the supports. My fault was to use PETG for the whole model and the support interface layer also. Perhaps it is worth mentioning this in the description so that other beginners can print this model.

@cm3dshop.de

Replying to @starkeeper :

thx for your comment. yes i used the petg/pla trick to get a smooth interface...and yes i forget to write it in the description...will do it now. Thx for your mention.

@Kgirouex

Replying to @cm3dshop.de :

I'm new and i don't understand what this means

@Emanuele_tech

Print Profile

0.16mm layer, 3 walls, 15% infill

There seems to be something wrong...when I insert the container, the lid doesn't stay closed

(Edited)

The designer has replied

@cm3dshop.de

@Emanuele_tech : did you remove the support filament unter the tray or something warped?

@Emanuele_tech

The support was removed without problems, maybe I'll try to scratch the base

@cm3dshop.de

Replying to @Emanuele_tech :

i checked the model again and can't see any issue in there...also there are other posts here with normal closing lid...so i am a bit confused of what the failture would be at your print.

@dmnk.rocks

my PETEG support layer does not stick at all, and I don't know what I did wrong. PLA is Bambu Matte, PETG is Bambu Basic. I just opened the file in Bambu Studio and hit Slice -> then Print.

The designer has replied

@cm3dshop.de

open the 3mf in the slicer, then go to the filament (petg settings) ...get 5 degrees more for printing ... and set the speed for the support a bit slower ... i heard alot of times that bambu petg have some strange behaviours ;)

@dmnk.rocks

Replying to @cm3dshop.de :

Will give it a try

@dmnk.rocks

Replying to @cm3dshop.de :

Made the Print today with the new Settings. Worked like a charm and came off absolutely clean. Thanks for the Heads Up. Will post a make once I come around to print the lid.

@user_874921311

你好，我的机型是X1C，使用了你的配置文件，只修改了耗材为BAMBU的PLA，测试了几次都是这些问题，打印其他模型就是好的，请问是我哪里配置错误了？

The designer has replied

@cm3dshop.de

this doesn't look good. Looks like a partial nozzle clog. Are you sure your filament is normal PLA?

@user_874921311

Replying to @cm3dshop.de :

是的，Bambu的PLA basic，这个耗材打印其他模型是没问题的，我继续测试下

@RyanZhang

Good design and quality, I love it. Thank you so much.

The designer has replied

@cm3dshop.de

Thx Alot!

@garant.alexandr

what filament did you used? I love the grey

@RyanZhang

Replying to @garant.alexandr :

eSun pla+

@Jocika

Print Profile

0.16mm layer, 3 walls, 15% infill

Das Model ist sehr schön, in druckdatei sind alles vorbereitet. Was mir sehr gefällt das ist die Hidden Greif, sieht gut aus und nützlich. Ich habe Magneten bestellt. Bis dan kann ich nicht zum Drucker.

The designer has replied

@cm3dshop.de

Hallo Jocika, das hinstellen und Nutzen geht auch ohne Magneten. Mit den magneten ist es dann etwas bedienerfreundlicher weil die Rutsche dann beim schließen nicht mehr nach hinten geschoben wird. ;) Vielen Dank auch für das uploaden der Bilder. Gruss Chris

@Jocika

Ich habe den Magnet erhalten, einfach ohne kleberstoff reingepresst. haltet wie Sau. passt die kontur von Modell sehr sehr gut. Siehe Bilder. Tolle Arbeit! Danke!

@cm3dshop.de

Replying to @Jocika :

Vielen dank für die tollen Bilder

@plapirate

Printed perfectly. The tray is a snug fit, but it's still easy to pull in and out. 11/10 would print again if I have another printer that needs a poop chute :)