Tapo c100 c110 c111 Bambu P1P P1S central door camera Remixed by FrancescoM

Remixed by

FrancescoM

3D Printer>3D Printer Accessories

Print Profile(4)

All

P1S

P1P

X1 Carbon

X1E

New Ver 2.0 - 0.2mm layer, 2 walls, 15% infill

Designer

38 min

1 plate

5.0(24)

SMALL PROFILE 0.2mm layer, 4 walls, 15% infill

Designer

46 min

1 plate

4.7(3)

LARGE PROFILE 0.2mm layer, 4 walls, 15% infill

Designer

47 min

1 plate

0.2mm layer, 2 walls, 15% infill

39 min

1 plate

Boost

220

141

Released

Description

04/12/23 New version 2.0

This is a remix of one of my projects.
We recommend using bioadhesive tape underneath the webcam attachment as shown in the photo.
I used 2 6x3mm screws

The cable is inserted on the profile as shown in the photo

Comment & Rating (72)

@ontheriver

Print Profile

New Ver 2.0 - 0.2mm layer, 2 walls, 15% infill

I did have to shorted it to get it to fit with my panda touch frame. I uploaded a print profile for anyone else with that issue.

The designer has replied

@FrancescoM

thank you for your vote and the new profile for panda touch

@ontheriver

Replying to @FrancescoM :

Thank you for the great model, just a tiny adjustment for a very specific use case

@FrancescoM

Replying to @ontheriver :

I also have a panda touch but I use the version above the display

@slappy76

Works Great! Thank you for the design. I saw another design that hangs off of the LCD display and it seemed ridiculous that you have to flip the camera up to open and close the door. This is WAY better Just a suggestion, rename the title to "Tapo c100 c110 c111 Bambu P1P P1S central door camera" or something similar. It was really tricky to find your listing otherwise. It came up with your corner cam and linked to this. I've read people wanting to focus the camera closer to the build plate. According to someone on Reddit, you can open up the camera with guitar picks or equivalent and shim under the lens with a piece of Scotch tape. Use only 1 layer because any more and the focus will be TOO close. For me, the factory focal plane is OK for now. Not too bad. I don't know how to give you five stars but ***** ;)

(Edited)

The designer has replied

@FrancescoM

thanks for the advice, I renamed as you suggested :-) I'll also try the focus suggestion

@geekgrrrl

Awesome idea but I find the camera sits a little low as seen in the pic

The designer has replied

@FrancescoM

In a few days I will publish a modified version to adjust the height.

@FrancescoM

hi, I created version 2.0 and I also put the photo of the shot. Try it and tell me if it's good or what I could improve. Thank you

@kidnapf1

Print Profile

New Ver 2.0 - 0.2mm layer, 2 walls, 15% infill

works great

The designer has replied

@FrancescoM

Thank you for great rating

@Voop

bracket was easily printed and all holes lined up, this is perfect for me, thank you

The designer has replied

@FrancescoM

Thank you for great rating

@meCoreyG

Print Profile

New Ver 2.0 - 0.2mm layer, 2 walls, 15% infill

love it.. has worked well so far for my camera. love that it is dead center.

The designer has replied

@FrancescoM

Thank you for great rating

@slickschoppers

this works perfectly for me, dead center, great view of the print, I couldn't ask for anything more. I saw somewhere a printed strip that you could stick to the side of the printer to run the power cable to the back, but haven't been able to find it again. if anyone sees it let me know. as far as this print goes, 5 stars works great!!!

The designer has replied

@FrancescoM

Hi, if you can find it you can share it with me thanks

@Fylde3dprinting

Replying to @FrancescoM :

https://makerworld.com/models/113366