Giant poop bucket
Copyright Claim
Giant poop bucket
Boost
60
101
88
Print Profile(1)
0.08mm layer, 2 walls, 15% infill
Designer
6.6 h
1 plate
Boost
60
101
88
3
375
284
Released
Description
This is the biggest poop bucket one can fit into the back of the printer comfortably. It is capable of holding enough poop waste for one insanely complex and multi coloured giant project.
Comment & Rating (88)
All
Print Profile
0.08mm layer, 2 walls, 15% infill
changed to .2mm layer. printed perfectly
The designer has replied
1
Reply
That looks awesome! Thanks for printing!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
Prints perfectly on my P1S.
The designer has replied
1
Reply
Thanks! That looks amazing!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
great poop bucket! I attached some Velcro tabs to hold it in place!
The designer has replied
1
Reply
Thank you very much! That picture looks awesome!
(Edited)1
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
The first print I did on my P1S. It printed flawless.
The designer has replied
1
Reply
Thanks! That looks stunning!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Wow that looks awesome! Thanks!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
It works great. It's especially nice for longer prints. I printed at 0.2 mm layer height which greatly reduced printing time. My only complaint is the walls are a bit thin and flimsy. I feel that if I put too much pressure on it, it will break.
The designer has replied
1
Reply
Thank you so much for your feedback. The 0.2 mm does work but slightly increases flimsiness as I noticed (not that it wasn't flimsy to begin with), and you are correct that it can snap under pressure, but I have so far dropped poop and rather large prints and it held out ok, and even when filled to the brim it shouldn't snap. I only made it thin to try to keep it at exactly 150g so that I can measure how much poop a specific print produced much more easily, and also because at least in my case I knew that I won't be touching the poop bucket too much. it's spacious enough to fill up only at the end of the month. But thanks to your advice I might design another thicker version.
0
Reply
Replying to @carefree.coding
Thank you for the explanation on your design. Good idea for keeping track of how much poop is produced.
(Edited)1
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
broke instantly but still useable
The designer has replied
0
Reply
I would love to know where it broke so I can make necessary adjustments to fix it. My original goal was to keep it at 150g, so measuring poop filament used would be simple math. However I am planning to make another version that's 200g and I would love to hear your feedback and to know where it broke so that I can remedy the problem.
0
Reply
Replying to @carefree.coding
it broke in the middle of the front side along the layer line
(Edited)1
Reply
Replying to @PhoenixCraft
Thanks for letting me know. I will try looking into maybe making a 3 layer version instead of 2 layer.
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
works great, pretty sturdy as well.
The designer has replied
1
Reply
Thank you!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
Works great
The designer has replied
1
Reply
Thank you!
0
Reply
Print Profile
0.08mm layer, 2 walls, 15% infill
quick and easy print.
The designer has replied
1
Reply
Thank you very much!
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial
© 2024 MakerWorld