Mystery Egg With Question Marks - NO SUPPORT
Copyright Claim
Mystery Egg With Question Marks - NO SUPPORT
Boost
134
179
64
Print Profile(4)
100% Sized 0.2mm layer, 2 walls, 5% infill
Designer
3.3 h
1 plate
50% Sized 0.2mm layer, 2 walls, 5% infill
Designer
57 min
1 plate
75% Sized 0.2mm layer, 2 walls, 5% infill
Designer
1.9 h
1 plate
100% Multi Color 0.2mm layer, 2 walls, 5% infill
Designer
18.2 h
1 plate
Boost
134
179
64
5
447
494
Released
Description
Hey!
Here is my adaptation of the mystery eggs. These make for awesome gifts, or to add some spice to your craft booths.
This fun print has questions marks all around the print with one BIG question mark that goes between the two halves. It is a press fit design and the two parts may be hard to press together. If this is the case for you please lower the size of the top by .5%
No support needed
Pictured in my is this model at 150%
4 standing up are 100%
For size comparisons. At 100% it can hole a 75% sized crystal dragon from cinderwing3d
If you would like a print without the question marks see my other egg https://makerworld.com/en/models/90038#profileId-96427
Comment & Rating (64)
All
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
printed good in transition color PLA. Printing in various sizes goes together well.
The designer has replied
2
Reply
thank you!
0
Reply
what’s the dimensions?
0
Reply
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
great print.
0
Reply
what size dragon can you fit in the 100% egg?
0
Reply
what is that baby dragon with the bigger one?
0
Reply
Boosted
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
nice the
0
Reply
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
made some from a bunch of left over filament.
0
Reply
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
printed great!
0
Reply
Print Profile
50% Sized 0.2mm layer, 2 walls, 5% infill
sehr hübsches Ei, genau die richtige Grösse für ein Kinderüberraschungsei!
0
Reply
Print Profile
75% Sized 0.2mm layer, 2 walls, 5% infill
great print, i print this with spare filament but probably reprint in better quality and filament
0
Reply
Print Profile
100% Sized 0.2mm layer, 2 walls, 5% infill
The designer has replied
0
Reply
may i ask why only 4 stars? This seems to have printed well
0
Reply
Thank you for sharing. The reason why I gave it four stars is that the way to open the egg is a bit difficult. Personal opinion.
0
Reply
this is awesome! thanks for making it available!! hope you get lots of points from this!
The designer has replied
1
Reply
Thank you! I hope it might take off and people will enjoy this. I was struggling with whether i should sell the file or not, and hey, its almost Christmas why not give it away.
4
Reply
Replying to @RaditivePrints
Im a Fan of your stuff. Your Keychain and Magnet stands, shelf brackets and prices have all made their way into my setup for vending.
0
Reply
Replying to @gleasonmagic
awesome! thanks for the compliment. It really means a lot!
0
Reply
are supports needed? BStudio warns there are floating parts ... ?
The designer has replied
0
Reply
no support. print awesome
0
Reply
no supports are needed
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-NoDerivatives
© 2024 MakerWorld