A1 mini AMS LITE space saver (top mount original)

aim6mac
3D Printer>3D Printer Accessories
Copyright Claim

A1 mini AMS LITE space saver (top mount original)

aim6mac
Boost
430
683
182

Print Profile(3)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1
0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
15.8 h
3 plates
4.8(30)
0.2mm layer, 4 walls, 10% infill
0.2mm layer, 4 walls, 10% infill
Designer
13.1 h
1 plate
4.6(11)
0.2mm layer, 4 walls, 10% infill
0.2mm layer, 4 walls, 10% infill
Designer
15.7 h
2 plates
4.2(14)
Open in Bambu Studio
Boost
430
683
182
20
1.1 k
662
Released

Description

since i got the A1 mini I wanted to make the footprint of it smaller , now I finally had some time to do it enjoy…

 

recommendations on the spool installation when not using 4 filaments at the same time on the AMS lite

3 filaments : 2 in front 1 in back

2 filaments : 1 front left , 1 back right or 1 front right , 1 back left

1 filament : 1 front left or 1 front right

 

The pins to connect the left feet and the top bar are tight and only go in one way correctly, if the holes do not line up turn them 180° until they do line up, otherwise this will end up with crooked left and/or top bar!

 

8 x M5 x 25mm bolts needed to assemble the whole unit.

ams lite
bambu a1 mini
a1 mini ams lite
ams lite mounting

Comment & Rating (182)

Please fill in your opinion
(0/5000)
level
@AniMeiGrrl
Very cool. Easy to print, easy to install. Thank you so much!
The designer has replied
1
Reply
level
@aim6mac
thank you!
0
Reply
level
@SLCPANTHERS
what is the purple thing on left?
0
Reply
level
@AniMeiGrrl
Replying to @SLCPANTHERS :
Death Star Port Poop Bucket.
0
Reply
level
@piranha
Woldn't it better to have it lower? i guess it would reduce the wiggling? i would love if you could publish version with reduced height.
(Edited)
The designer has replied
2
Reply
level
@aim6mac
i wish i could design it lower , but the hotend wont allow that to happen since when the hotend goes all the way to the top it will collide with the filament spools.
0
Reply
level
@piranha
Replying to @aim6mac :
Ah I see now. Great job! When I get my A1, your model will be the first one printed for sure :)
2
Reply
level
@aim6mac
Replying to @piranha :
will save lots of space for sure, u won't regret it :)
0
Reply
level
@jerry2k
There is a gap of approximately 1mm and there is no contact with the desktop
The designer has replied
0
Reply
level
@aim6mac
thats most likely printer calibration... mine printed fine although when u put the AMS system on top of it with the spools, it won't make any difference.
0
Reply
level
@jerry2k
great！
1
Reply
level
@jerry2k
I added a cushion underneath
0
Reply
level
@dentistry3dmake
Print Profile
0.2mm layer, 4 walls, 10% infill
es y termina pareciéndose a la bambu A1 sin querer queriendo XD me encantó maximizar el espacio para poder imprimir en torre, que es algo habitual en mi laboratorio, trabajar en torre para maximizar los espacios!
The designer has replied
1
Reply
level
@aim6mac
Me alegro que funcione bien :)
0
Reply
level
@user_233779599
Hello, thank you very much! btw why must this part be so high? Can I reduce the height a few cm ? If yes, what will be the minimum height?
(Edited)
The designer has replied
1
Reply
level
@aim6mac
otherwise the printhead will collide with the spools.
1
Reply
level
@cyberjo50
so far so good. thank you
The designer has replied
1
Reply
level
@aim6mac
looks great! enjoy..
0
Reply
level
@JameJame
Looks pretty cool! it is very stable and sturdy. Excellent upgrade. Takes up a reasonable amount of space now!
The designer has replied
1
Reply
level
@aim6mac
I'm very pleased that you liked the mod, thank you!
1
Reply
level
@maldude18
Print Profile
0.2mm layer, 4 walls, 10% infill
great print! Pins were an extremely tight fit and didn’t line up perfectly but it worked out. Its stable and doesn’t shake at all.
The designer has replied
1
Reply
level
@aim6mac
if the pins didn't line up , it means u have to turn it around, it only fits one way correctly , check mine it was a perfect fit. thanks!
0
Reply
level
@user_114219733
Boosted
Amazing design great space saver for the AMS strong and sturdy. I even added an extra piece due to the height was very easy to assemble.
The designer has replied
0
Reply
level
@aim6mac
looks awesome in all black too!
0
Reply
level
@bradle48
Boosted
Great print! Saving a lot of space vs the other options I tried with the A1 Mini and AMS Lite.
The designer has replied
0
Reply
level
@aim6mac
oh thank you, glad u liked it, enjoy!
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

AMS mini Top Mount for A1

AMS mini Top Mount for A1

Brandon Li
3
5
1
Bowden PTFE mount for original External Spool

Bowden PTFE mount for original External Spool

nachovilly
6
8
16
Gridfinity Spacer Generator

Gridfinity Spacer Generator

ioio72
1
19
9
PTFE Tube Remover Tool AMS A1 and A1 mini

PTFE Tube Removal Tool for AMS A1 and A1 mini

WaterMeloon
10
269
667
PrivacyTermsGuidelinesFAQCookie PolicyCookie SettingsHot Searches
© 2024 MakerWorld