Ratchet Fidget
Copyright Claim
Ratchet Fidget
Boost
375
718
348
Print Profile(6)
V2 longlife | 0.2mm layer, 2 walls, 15% infill
Designer
27 min
1 plate
V1 | 0.2mm layer, 2 walls, 15% infill
Designer
25 min
1 plate
V1 set of 3 | 0.2mm layer, 2 walls, 15% infill
Designer
1 h
1 plate
V1 for A1 | 0.2mm layer, 2 walls, 15% infill
Designer
29 min
1 plate
Click to see more
Boost
375
718
348
72
1.5 k
2.4 k
Released
Description
NEW
funny clicky fidget ratchet with knurled knob on the one side and hex nut on the other.
basic filamen- (instead of matt) providing better click and longer life due to less wear over time.
carefully brake free the lever from the surface bevor assembly!
new longlife version:
- double-spring ensures long life
- open heart - better sound
______________________________________________________________________________________________________
V1
- single lever provide more precise and predictable click
- the spring-loaded lever on rotor allows more tention but also more spring travel = results in better sound and less wear over time
- shaft guide compensate the tilt resulting from single lever
- no supports needed
origin:
Comment & Rating (348)
All
Print Profile
V1 for A1 | 0.2mm layer, 2 walls, 15% infill
it’s so fun to play with. the click is very satisfying. I felt the need to make it bigger and I would definitely recommend doing that, the sound difference is amazing.
The designer has replied
1
Reply
ahha Mate I never thought about scaling it! Very nice :)) Thanks for sharing
0
Reply
Boosted
Dang, now i need to do that xD good idea!
0
Reply
Print Profile
V1 | 0.2mm layer, 2 walls, 15% infill
Nice print, looking forward to try it out! :-) I have found out that the printed model has a really minor defect when printing the ratchet arm, it prints bridge, that is curved in the air, which the printer cant do… So thats why it is straight line. If it is normal and it is intended, then tell me. But other than than, love it! Thank you for your design :-)
(Edited)
The designer has replied
1
Reply
Hi Jakub! Thank you for the reply and your reminder ;) You are absolutely right, I didn't recognized this as a design issue- but it is- no doubt! Nevertheless it has no effect (except esthetic issue) on the model. as you can imagine (I just write it down in case someone will find this usefull for overall understanding) there are two opposite target to get at this point: 1) clearance 2) spring form = curve in the air :) I hoped the first "in the air" layer will have slight contact due to adhesion (perhaps it hat in the first prototyped but then after increasing the gap I didn't mention the moment it turned to the straight line). Perhaps it will also work with less gap but then you have to break the lever free bevor assembly- less plug and play :) I will decently think about it for some time, maybe will come up with an idea. Thank you for reporting mate!
(Edited)1
Reply
Replying to @mounty
might cause some people issues if that first unsupported layer drags around. an easy fix might be to give that 'spring' a slight angle and then it won't extend so far without any support, but it'll decrease the likelihood issues. will also make the spring slightly weaker. but the bigger concept is potential filament drag issues causing problems elsewhere in the print. otherwise, nice! good job. :-)
0
Reply
Print Profile
V1 | 0.2mm layer, 2 walls, 15% infill
printed beautifully with Inland gold Silk PLA!!
The designer has replied
2
Reply
😍thank you for the pic, looking great!
(Edited)1
Reply
Print Profile
V1 | 0.2mm layer, 2 walls, 15% infill
very satisfying click
The designer has replied
0
Reply
hi! thank you for sharing pictures? I love the color? What is it? Is it a Bambu filament?
0
Reply
yep its a red PETG bambu filament
(Edited)1
Reply
Print Profile
V1 | 0.2mm layer, 2 walls, 15% infill
Really amazing at how fine the resolution is on the A1. Printed two of these for nice color combo with Bambu PLA.
The designer has replied
1
Reply
Bambu did a great job! only that makes such stuff possible. turned out great! thanks for sharing pictures mate!
0
Reply
Print Profile
V1 for A1 | 0.2mm layer, 2 walls, 15% infill
tuned out great, printed it with pla basic and has no issues. used my new p1s with top off and door open on sport setting nothing changed
The designer has replied
1
Reply
thank you for the pics! 🫡
0
Reply
Print Profile
V1 | 0.2mm layer, 2 walls, 15% infill
huge improvement over the original, thanks.
The designer has replied
1
Reply
Thank you! :)
0
Reply
Boosted
Bigger is better. (It also gets alot louder)
The designer has replied
0
Reply
:DD so funny I never tried it :D thanks for sharing
0
Reply
Boosted
Print Profile
V2 longlife | 0.2mm layer, 2 walls, 15% infill
Strength Issue:Print comes out fine and worked well. if you ever turn it the wrong way the print is compromised and will fail. After a while the dial snapped the middle support. Had to toss
The designer has replied
0
Reply
Do not turn the wrong direction ;) operating failure. Why you blame the model? Go and turn you car or door key the wrong direction 🤔
0
Reply
Boosted
Replying to @mounty
Agree 100%, just hard to tell that to a 6 year old who doesn't understand fully yet :D. Might print it again with a stronger filament and see if that helps
0
Reply
Replying to @BearDooks
I understand. Of course I had tried to design biderectional toy but, in to make a satisfying feeling while clicking i went witch an wedge teeth form on outer ring in order to provide rising tension before click. But, thank you for the idea with kids… stupidity i didn’t thought about this use case :) I will Design a biderectional version soon. 🔜
0
Reply
Boosted
Print Profile
V2 longlife | 0.2mm layer, 2 walls, 15% infill
The best clicky fidget very good feedback
The designer has replied
0
Reply
thank you!
0
Reply
License
This user content is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld