特点：

1.铰链翻转部分磁吸固定，可有效控制铰链产生的虚位；

2.采用2滑动条和1固定条结构，可控制部分移动产生的大角度变形，固定时直接拧紧固定条的螺丝；

3.在不影响强度的前提下实现无中缝设计，左右可大范围拖动；

Features:

1. The hinge flip part is fixed by magnetic attraction, which can effectively control the virtual position of the hinge;

2. The structure of 2 sliding bars and 1 fixed bar can control the large-angle deformation caused by partial movement. When fixing, directly tighten the screws of the fixed bar;

3. The design without center seam is realized without affecting the strength, and it can be dragged in a wide range left and right;

性能参数：

宽度最短7mm，最长95mm，适用大部分印刷；

整体尺寸150*150mm，非常小；

Performance parameters:

The shortest width is 7mm and the longest is 95mm, suitable for most printing;

The overall size is 150*150mm, very small;

使用教程：

1.先大致确认涂刷位置然后固定钢网；

2.安装PCB并拖动滑动块，拖动至钢网1mm以内间隙，拧紧固定条螺丝；

3.重新调整钢网位置，精准对准焊盘，完成；

Usage tutorial:

1. First roughly confirm the brushing position and then fix the steel mesh;

2. Install the PCB and drag the slider until the gap is within 1mm of the steel mesh, and tighten the fixing bar screws;

3. Re-adjust the position of the steel mesh and accurately align it with the pad, and it is done;

安装教程：

物料：

1.M3螺丝_长度6mm：8颗，长度8mm：11颗；

2.M5滚花螺丝_长度12mm：3颗；

2.螺母_M3方螺母：15颗，M3六角螺母：4颗，M5六角螺母:3颗；

4.磁铁_5*1mm磁铁：8颗；

5.铰链_如图尺寸：2个；

Installation tutorial:

Materials:

1. M3 screws_6mm in length: 8, 8mm in length: 11;

2. M5 knurled screws_12mm in length: 3;

2. Nuts_M3 square nuts: 15, M3 hexagonal nuts: 4, M5 hexagonal nuts: 3;

4. Magnets_5*1mm magnets: 8;

5. Hinge_size as shown: 2;

步骤：

1.方螺母塞入方孔，六角螺母塞入6脚孔，拧螺丝，M3*6螺丝使用在铰链，m8螺丝使用在滑块；

2.滚花螺丝直接安装即可；

3.磁铁NS级做标记再安装，使用704胶或者502脚粘接，注意磁铁顶端必须与周边平面平齐！！！

4.三条中间为固定条，上下为滑动条，滑动条可以拧紧，固定条在移动时拧松；

Steps:

1. Insert the square nut into the square hole, the hexagonal nut into the 6-pin hole, and tighten the screws. M3*6 screws are used for hinges, and M8 screws are used for sliders;

2. Knurled screws can be installed directly;

3. Mark the NS grade of the magnet before installation, use 704 glue or 502 pin bonding, and note that the top of the magnet must be flush with the surrounding plane! ! !

4. The middle of the three strips is a fixed strip, and the upper and lower strips are sliding strips. The sliding strip can be tightened, and the fixed strip can be loosened when moving;

物料图片：

Material pictures: