Pikachu wire frame // <14g // no support needed by Roy van Duijnhoven

Roy van Duijnhoven

Art>Other Art Models

Print Profile(1)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 6 walls, 20% infill

Designer

2.5 h

1 plate

2.2(5)

Open in Bambu Studio

Boost

115

196

228

Released

Description

Pikachu Wire frame // <14g // no support needed

Printed in 2,5 hours.

I recommend using adhesive spray or a glue stick, but i added a brim so it is also possible to print it without.

Beautifull piece of art that is loved by young and old!

Gonna print them all

UPDATE: added a new print profile with better adhesion!

If you want to slice the model by yourself, make sure you lower the Z-height by 1,5mm or more. This way you create a bigger surface that touches the build plate, add an outer brim on it too. SEE PICTURES.

Comment & Rating (17)

@ChadMikeInnis

Print Profile

0.2mm layer, 6 walls, 20% infill

Used glue after reading comments. Print finished ok, but the bottom layer was barely hanging on to the plate by the tiny brim and the lower layers are pretty messy. Also, there seems to be a pause written into the g-code about a quarter of the way up the print that I had to manually resume after. Wouldn’t suggest printing this.

The designer has replied

@royke1999

i’m sorry I have updated the profile right now, I had uploaded the wrong one by accident

@GoneToPlaid

Print Profile

0.2mm layer, 6 walls, 20% infill

Bed Adhesion Issue

The designer has replied

@royke1999

Did you print it straight from my print profile (and use adhesive spray as I suggested)? Otherwise if you slice the model by yourself, you need to lay it flat on the biggest surface and then reduce the Z height by 1mm. So the model will be flatter on the build plate and use a brim as well. Try and let me know if it worked😜

@antho77m

Bed adhésion issue too. I change many filaments, temp, start speed, fan power more and less, impossible to start your model. I completly remake calibration of the bed : impossible again. all other prints start without glue or adhésions products, i don’t whant start glue my bed just for this model. there is a problem in your settings.

@royke1999

Replying to @antho77m :

I now updated the print profile to increase the bed adhesion.

(Edited)

@Angi

Very rare do I have bed adhesion problems-this model, attempted multiple times, and would not stick. Cleaned bed, still nothing, so sad :(

The designer has replied

@royke1999

Updated the print profile to increase the bed adhesion.

@user_3915161876

Print Profile

0.2mm layer, 6 walls, 20% infill

abfall

The designer has replied

@royke1999

Updated the print profile to increase the bed adhesion.

@user_1928187999

加了胶水，连续试了4次热床无法附着

The designer has replied

@royke1999

您是直接从我的打印文件中打印出来的吗（并按照我的建议使用了喷胶）？否则，如果您自己切割模型，您需要将模型平放在最大的表面上，然后将 Z 高度降低 1 毫米。这样，模型就会平整地放在构建板上，同时还能使用帽檐。试试并告诉我是否有效😜。

@Justinvelthuijs

Boosted

Lovely design

@Printable3D

Print Profile

0.2mm layer, 6 walls, 20% infill

@Angi

Print Profile

0.2mm layer, 6 walls, 20% infill

Bed Adhesion Issue:something is off on this model attempted a few times.

The designer has replied

@royke1999

Updated the print profile to increase the bed adhesion.

No more

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.