Can Lid Opener & Lid Saver Cap & Keychain

Remixed by

Can Lid Opener & Lid Saver Cap & Keychain

Remixed by
Boost
61
121
37

Print Profile(3)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

A1mini -0.2mm layer, 2 walls, 15% infill
A1mini -0.2mm layer, 2 walls, 15% infill
Designer
59 min
1 plate
5.0(15)

0.2mm layer, 4 walls, 15% infill
0.2mm layer, 4 walls, 15% infill
Designer
1.3 h
1 plate
4.7(10)

0.24mm layer, 2 walls, 15% infill
0.24mm layer, 2 walls, 15% infill
Designer
46 min
1 plate
5.0(1)

Open in Bambu Studio
Boost
61
121
37
23
223
168
Released

Description

Simple can opener and to protect the drink.

For easy opening of the cans and to protect the hole so that the bees / wasps stay out.

It has an extra hole at the top to use it as a keychain.

The instructions are really simple - guide the open slot of the printed part over the can tab and lift it up to open the can.

Turn the printed part with the tab 180 degrees to block the opening for the can.

It was reinforced and edges smoothed.

If you like this design and want to support me,

please boost this design (click on the little rocket 🚀 or the "BOOST" button) 🙏👍

 

==========================================================================

Einfacher Dosen Öffner und um das Getränk zu schützen.

Zum leichten Öffnen der Dosen und um das Loch zu schützen, so das die Bienen / Wespen draußen bleiben.

Es hat extra oben ein Loch, um es als Schlüsselanhänger zuverwenden.

Die Anleitung ist wirklich einfach – Führen Sie den offenen Schlitz des Druckteils über die Dosenlasche und

heben Sie ihn an, um die Dose zu öffnen.

Drehen Sie das gedruckte Teil mit der Lasche um 180 Grad, um die Öffnung für die Dose zu blockieren.

Es wurde verstärtkt und Kanten geglättet.

Wenn dir dieses Design gefällt und du mich unterstützen möchtest,

dann booste dieses Design bitte (klicke auf die kleine Rakete 🚀 oder den „BOOST“-Button) 🙏👍

 

Comment & Rating (37)

Please fill in your opinion
(0/5000)

Print Profile
A1mini -0.2mm layer, 2 walls, 15% infill
good fast Print.
0
Reply
I've already printed the lids, great expansion :-)
The designer has replied
Show original
1
Reply
Thank you for the Boost.
0
Reply
Boosted
Print Profile
A1mini -0.2mm layer, 2 walls, 15% infill
Awesome!!! Was the hit at the festival
The designer has replied
Show original
1
Reply
Hello, thank you for the positive message ;-))
Show original
0
Reply
Boosted
Great design and my nailless ass needs this badly.
The designer has replied
1
Reply
Thank you for the Boost
0
Reply
Boosted
Print Profile
A1mini -0.2mm layer, 2 walls, 15% infill
Made some for W:O:A 2024, works great!
The designer has replied
1
Reply
Thank you for the Boost
0
Reply
Boosted
Works great!
The designer has replied
1
Reply
Thank you for the Boost
1
Reply
Boosted
Print Profile
A1mini -0.2mm layer, 2 walls, 15% infill
Printed for my parents, who experienced difficulty opening cans due to hand problems—it works wonderfully and makes opening much easier
Show original
1
Reply
Print Profile
0.2mm layer, 4 walls, 15% infill
it doesn't snap to the top of a soda can
1
Reply
Print Profile
A1mini -0.2mm layer, 2 walls, 15% infill
Printed well and works on smaller cans too!
1
Reply
sehr schönes Modell und super Druck 👍 😍
1
Reply

This remix is based on

This source model was used for remixing/sharing before its license was restricted.
Dosenöffner m und verschliesbar

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike