HueForge Stained Glass Macaw

HueForge Stained Glass Macaw

Boost
97
148
7

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.08mm layer, 1 walls, 100% infill
0.08mm layer, 1 walls, 100% infill
Designer
4.6 h
2 plates
4.7(3)

Open in Bambu Studio
Boost
97
148
7
11
91
23
Released

Description

I used HueForge Lithophane Blending Type and an AI created image to make this “stained glass" Macaw print in TWO parts. The first part has white, blues and black of the foreground. The second part blanks out parts of the bird and provides the reds and yellows for the background. The image halves are tailored to yield green leaves, though no green filament is required for either half of the model.

Both parts have very thin base layers, so special care is needed to remove them from the print bed. It is probably best to cool them completely before trying.

When joining the two parts be sparing with the adhesive, especially in the lighter parts. The adhesive will change the colors if it is not behind the black or red parts. I just used some around the black parts and around the very edge to keep the glue from showing. If spread thin and uniformly, it should not show too much.

It uses 0.08mm layers to speed printing with minimal lose in detail.

 

Part 1

Project: Macaw_Part_1.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

The Model is 150x167.49mm in size
You may print at higher layer heights below the Min Depth of 0.16mm
The Max Depth is 1.4mm and the Actual Depth is 1.3mm

Filaments Used:
PLA PolyLite Natural Transmission Distance: 21
PLA PolyLite White Transmission Distance: 5
PLA Overture Blue Transmission Distance: 4.2
PLA HueForge Navy Blue 2.2 Transmission Distance: 4
PLA PolyLite Black Transmission Distance: 0.3
This print uses 5 unique filaments

Swap Instructions:
Start with Natural
At layer #2 (0.24mm) swap to White
At layer #4 (0.4mm) swap to Blue
At layer #8 (0.72mm) swap to Navy Blue 2.2
At layer #14 (1.2mm) swap to Black for the rest.

 

AMS/MMU users with four slots will need to manually swap out the natural filament for black on the first part once the initial two layers are done and before the Navy Blue is finished.

 

Part 2

Project: Macaw_Part_2.hfp
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm

The Model is 150x167.49mm in size
You may print at higher layer heights below the Min Depth of 0.16mm
The Max Depth is 1.4mm and the Actual Depth is 1.4mm

Filaments Used:
PLA PolyLite Natural Transmission Distance: 21
PLA Polylite TD1 Lemon Yellow Transmission Distance: 5.5
PLA Overture Red Transmission Distance: 4.8
PLA PolyTerra Army Red Transmission Distance: 0.3
This print uses 4 unique filaments

Swap Instructions:
Start with Natural
At layer #2 (0.24mm) swap to Lemon Yellow
At layer #5 (0.48mm) swap to Red
At layer #12 (1.04mm) swap to Army Red for the rest.

 

If substituting filaments, pick ones with the closest TD values. Use a Natural white, if possible. Otherwise, pick the one with a TD > 10 to minimize the color change it will cause.


Documentation (2)

Other Files (2)
Macaw_Part_1_describe_624918b2-266a-4366-a059-d0ce0768491f.txt
Macaw_Part_2_describe_9e817fc8-e7f3-4543-83ca-803b03bb920a.txt

Comment & Rating (7)

Please fill in your opinion
(0/5000)

Printed very nice, good model
0
Reply
Phantastisch, vielen Dank, gedruckt auf den A1. Kam perfekt raus, bin gerade dabei es auf 150% zu skalieren und zu Drucken. Achtung nur X+Y vergrößern Z muß gleich bleiben👋
(Edited)
0
Reply
Print Profile
0.08mm layer, 1 walls, 100% infill
Vielen Dank!!!
0
Reply
Print Profile
0.08mm layer, 1 walls, 100% infill
good design and concept
0
Reply
Boosted
Awesome!
0
Reply
Boosted
Beautiful piece. Can't wait to print it.
0
Reply
Print Profile
0.08mm layer, 1 walls, 100% infill
0
Reply
No more