Heavy Base for Tape Dispenser, Multi-size/Modular

Remixed by
Copyright Claim

Heavy Base for Tape Dispenser, Multi-size/Modular

Remixed by
Boost
40
137
16

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

All sizes, print 1 plate for the size you want.
All sizes, print 1 plate for the size you want.
5.8 h
4 plates
4.3(9)

Open in Bambu Studio
Boost
40
137
16
12
158
56
Released

Description

This is base that replaces the spacers in my original model Tape Dispenser, Multi-size/Modular

https://makerworld.com/en/models/492596

 

This base allows for the middle spacer to be filled with sand or the material of your choice.

Depending on the material you choose, you will obviously get different weights.

For example with the 2 inch spacer I achieved a little over 300 grams using dry sand.

Now, I am well aware that 300g is not super heavy but if you build a modular dispenser, the weight will add up.

I am sure denser/heavier materials can be found (epoxy resin? lead shot?)

I did not want to make the part bigger because I did not want to affect the look of the dispenser.

Printing

There is nothing special about this print, no supports or anything special needed, layer height and material to your liking.

Assembly

Just fill with material of choice to just below the tapered lip.

glue the top with a very light bead of CA glue or epoxy.

Enjoy!

And If you have a minute, check out my other models!

 

Comment & Rating (16)

Please fill in your opinion
(0/5000)

Print Profile
All sizes, print 1 plate for the size you want.
thanks
0
Reply
Very nice! I used BBs to weigh it down.
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
none of the models exist except the 1"and it didn't print great
The designer has replied
0
Reply
You will find them all in the object view of the slicer. You need to tick the relevant ones as mentioned in the print profile title. They all printed well for me so I'm not sure what issues you had, perhaps share a photo and we can try to diagnose the issue.
0
Reply
Replying to @trusteddev :
yes but as other comments have mentioned only the 1" will load. if you select any of the others it will not load. and if you just try to print them all at once it will only print the 1"
0
Reply
Replying to @khoward :
I looked into this further and it's a bug in the mobile app. It worked fine in the desktop slicer. I've now updated the profile so that each size is on it's own plate which will hopefully work for you. What kind of print issues did you have?
0
Reply
Bambul Studio cannot open the “spacer 2 inch” correctly. A repair by Bambu Studio was also unsuccessful. Perhaps you can take another look at this.
0
Reply
I suspect you may have been using the mobile app which seemed to dislike slicing the models. I've now changed the profile so that each size is enabled on it's own plate.
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
Ordered lead shot for it.
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
Worked great but the tolerances can be improved on.
0
Reply
concept is great unfortunately you can only print the 1" it fails to slice any other size
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
Good upgrade for the tape dispenser, although be cautious with it if you fill it with sand as it easily gets into the glue and messes with the fitment of the lid.
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
0
Reply
Print Profile
All sizes, print 1 plate for the size you want.
0
Reply