Lunban Box for Wedding candy box，鲁班盒早生贵子婚礼盒
Copyright Claim
Lunban Box for Wedding candy box，鲁班盒早生贵子婚礼盒
Boost
361
420
67
GIF
GIF
In Contest
Wedding DecorPrint Profile(1)
0.2mm layer, 2 walls, 15% infill
Designer
23 h
4 plates
Boost
361
420
67
90
646
44
Released
Description
文件只需要2个608ZZ的轴承就可以。
在中国一般会在结婚时使用，里面会放上红枣、花生、桂圆、莲子，寓意着早生贵子。
插销是有多的，给了几个不同大小的尺寸
The file only requires two 608ZZ bearings.
In China, it is usually used when getting married. Red dates, peanuts, longan, and lotus seeds are placed inside, which means that you will have a child early.
There are many pins, and they are given in several different sizes.
Comment & Rating (67)
All
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
Absolutely beautifully designed and fully functional. Printed perfectly and easy to assemble. Thank you for sharing!
The designer has replied
2
Reply
It is recommended to put some anti-slip tape on the bottom
(Edited)1
Reply
Boosted
Replying to @user_844018121
Thank you for the tip! I love the design. Everyone I show is in awe of the beauty and magic of the box.
0
Reply
Boosted
I like that color combination. What filament is that blue
0
Reply
Boosted
I wanted to make something somewhat unique for a friend of mine who is getting married later this year, and this seemed like the perfect gift. As you can see from the first photo, it turned out beautiful!
But, for the life of me I can not figure out how the box stays together as one piece. The center post (in two parts) has smaller projections on either end yet the box top and bottom pieces do not have cutouts for those projections, only for the wider post. So I wound up removing the projections and lengthening the center post as shown in the 2nd photograph. That solved that problem, but I can not figure out how this box is supposed to stay as one piece. If someone goes to move it, they would naturally grab the top to lift the box, but the only thing that would be lifted is the top piece itself. Can someone explain to me what I need to do so that the box is one piece rather than loose pieces?
(Edited)
The designer has replied
0
Reply
In mid-July I will release a version fixed with screws, which will be stronger
0
Reply
This bump is for the 608ZZ bearing.
0
Reply
完工了，设计很好，表面的图案删了，我放温
The designer has replied
0
Reply
可以的。我没合并就是为了方便删除换自己想要的图
0
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Boosted
我看你的摆盘文件里面那些小立柱为什么不立着摆放啊，加裙边应该就可以了，这样打印出来更圆，放在盒子里面更顺滑吧，还有中间的大轴需要用到胶水吧，这些轴的打印填充是否需要100%啊？
The designer has replied
0
Reply
不用。横着放增强强度。立着放层黏原因，可能容易断。
1
Reply
PETG不需要胶水，PLA可能需要，收缩率不一样，基本能卡的很紧，PLA收缩小需要胶水，立着打容易断，而且需要支撑，躺着打不需要支撑，而且强度高。不用100%直接默认都可以。强度高于立着打100%填充都有考虑到
0
Reply
Boosted
Replying to @user_844018121
哦，对哦，我都忘记立起来打印层黏问题导致的强度低的问题了，明白了。
0
Reply
设计很好看，想请教一下这么大面积，打印过程容易翘边吗？怎么样能避免翘边呢？
The designer has replied
0
Reply
底部已经尽量做了防翘了，但是收缩率大，PETG还是难免会翘
0
Reply
Replying to @user_844018121
感谢大佬答疑 🙏
0
Reply
会不会断，怕结婚当天转断了
The designer has replied
0
Reply
怕断掉就在轴承外圈加胶水。这是唯一连接点，还有个更耐用的版本还在改。用的是螺丝
2
Reply
断了就代表一生一世断断不能分离，挺好的
0
Reply
Boosted
我再结婚一次的时候，得打三四个
The designer has replied
1
Reply
哈哈哈哈哈，过年的时候也可以放
0
Reply
Boosted
出个组装教程哈 狮子哥
The designer has replied
0
Reply
很简单的。4个短的在盖子上。四个长的插销在底座上。中间二合一插上轴承放进去。就好了
0
Reply
Replying to @user_844018121
这是不是说反了 长的在盖子上 短的才是底座
0
Reply
Will it work if scaled down for the A1 Mini?
The designer has replied
0
Reply
If you reduce the size, the bearing will be too small.
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-NoncommercialRemixes (2)
© 2024 MakerWorld