Gyro fidget spinner 9 rings
Copyright Claim
Gyro fidget spinner 9 rings
Boost
35
48
20
GIF
GIF
Print Profile(3)
0.2mm layer, 2 walls, 15% infill
Designer
50 min
1 plate
0.2mm layer, 2 walls, 15% infill
Designer
46 min
1 plate
0.2mm layer, 2 walls, 15% infill
Designer
51 min
1 plate
Open in Bambu Studio
Boost
35
48
20
3
68
75
Released
Description
Another version of the popular Gyro Fidget Spinners. This time 9 circles. It has a diameter of 5 cm. It is slightly movable immediately after printing. 6 circles can be separated and reassembled. It does not require any special printing settings. Enjoy it!
Another one is here.
Comment & Rating (20)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
great print and fun to play with.
The designer has replied
0
Reply
ooh nice, black is always nice!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
easy to print und works fine
The designer has replied
0
Reply
oh Nice color. thank you for the rating.
0
Reply
very nice, easy to print and makes a lot of fun! thx for creating
print with easyprint rainbow
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
printed well, but I think you might have flown a little too close to the sun with the amount of rings lol hard to manipulate the fidget.
The designer has replied
0
Reply
I have another one with 10 rings and a ball in the middle :-)
0
Reply
Replying to @3DUDEK
nice!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
love it! spins well and is fun to play with
The designer has replied
0
Reply
Thanks for the rating. I'm glad it gives you pleasure.
0
Reply
Boosted
No Problem!
The designer has replied
0
Reply
Perfect! Glad to hear it:-). Thanks for the boost.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Other Issues:used the print profile and every layer stuck together at the seam except the very center
The designer has replied
0
Reply
Hello. As you can see in the video, the spinner is mobile immediately after removing it from the mat. The only fault may be in the filament. Did you use PLA? Nozzle 0.4mm?
0
Reply
and this is why I hate giving an honest review… it’s my fault if your model doesn’t work perfectly. yes I used pla and with .4 nozzle. I printed it from my phone with your profile settings. I didn’t tweak anything which is where I probably went wrong. idk. sorry for being honest
0
Reply
Replying to @mcgill_jeff
I'm sorry, but I didn't write anywhere that it was your fault. I have no problem with your review either. I'm just looking for the reason for your failure. As we both know, there are many factors involved in 3D printing. The quality or humidity of the filament can also be one of the reasons. Some melt differently than others at the same temperature. That is why, for example, temperature towers are printed. This model is demanding on tolerances (between individual rings is 0.2-0.35mm) and therefore I am convinced that the problem is in the filament and not in you. 3D yew is supposed to be fun and this model is not time or material intensive so I'm sure you won't be disappointed. Sorry for the trouble, but I didn't anticipate it.
Have a nice day
Pavel
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld