Captain America shield fridge magnet by crabstiks

crabstiks

Household>Decor

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 50% infill

Designer

3.7 h

1 plate

4.4(8)

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

3.2 h

1 plate

4.0(8)

9 shields on a plate 0.2mm layer, 2 walls, 50% infill

5.8 h

1 plate

5.0(1)

Boost

202

257

284

Released

Description

A fridge magnet design based on Captain Americas shield from the marvel avengers movies.

It needs 2 magnets 3mm diameter by 10mm length, these push in after the print, there's no need to pause it.

The model is split into three objects to allow easy selection of colours in Bambu Studio

Comment & Rating (26)

@BurlySpain

Print Profile

0.2mm layer, 2 walls, 50% infill

Great

@MofWI

Print Profile

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

Great concept! Looks so good! Two ideas, their were several filament changes red to white and back, due to the separate objects internally. Also, you should change your print profile to include Variable Layer Height for smoothness. Looks great on the fridge!

@sutton.steve

Print Profile

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

Lines don’t line up causing the print to look bad. Magnet holes are 28mm deep (not a typo, 28 mm deep), by 5.5mm wide Printed with overture red pla, overture matte white pla, and esun blue pla+ on X1 Carbon. Overall, I do not reccomend this profile.

Other Issues

@al0yyy

Print Profile

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

great print!

@thibaud

Print Profile

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

Déçu, la pièce n'est pas droite, le fichier 3D n'est pas plat !!!! Le rendu est mauvais à cause d'un décalage à l'impression

@thibaud

Déçu, la pièce n'est pas droite, le fichier 3D n'est pas plat !!!! Le rendu est mauvais à cause d'un décalage à l'impression

@tooling_lee

Hard time getting the white in the center to print deep enough... need to figure that out...

@user_484812875

Print Profile

Scaled for 6x3 Mags and optimized for multicolor_0.16mm layer, 2 walls, 15% infill

@davglass

Print Profile

0.2mm layer, 2 walls, 50% infill

Printed well, but I can’t seem to find any magnets the proper size needed.

The designer has replied

@crabstiks

Hi, Thank you for downloading my model. I bought the magnets from aliexpress. Here's the link if that helps, though remember to select the 3x10 magnets before checking out as the link has different sizes. https://a.aliexpress.com/_EGs3jz3

@PaulBPunkt

Print Profile

0.2mm layer, 2 walls, 50% infill

The model is good, but because the individual segments are dyed through, the color has to be changed at almost every layer height, which on the one hand increases the printing time enormously and on the other hand produces a lot of waste.

The designer has replied

@crabstiks

I did it that way so the rear looks good toi