Stormtrooper 13 Model - 3D Innovators Studio

Remixed by

Stormtrooper 13 Model - 3D Innovators Studio

Remixed by
Boost
99
207
12

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
6.5 h
5 plates
4.9(9)

Boost
99
207
12
3
220
71
Released

Description

Description

Here is a general overview:

Model Details:

Edits:

Added short neck that fits better with big heads in the Dummy13 models.

Separated the calves to better print using supports.

Colored Mask and Chest plate and organized for better printing.

 

Disclaimer: Some of these parts were originally designed for Lucky13, I'm putting this series to better fit Dummy 13 instead.

 

The profile has 5 plates,

  1. Print each plate with or without supports/brim according to the plate title.
  2. Plate with the calves and mask ensure you use brim and tree supports and carefully remove these from the calves, the calves are a challenge but can be done carefully.
  3. Follow Original Dummy 13 video for guidance on assembly.

Additional Notes:

  • Post-Processing: After printing, I carefully removed the supports.

I'm printing in PLA however it is recommended to print in PETG 15 mm layer height infill 15%.

 

Enjoy,

I wanted to share some pictures of how it looks and compared to other figures I had for comparison. I also wanted to share that it printed and the settings I used to put it together and how it worked out, I did not edit anything on the models on this profile, my work was limited to sharing my profile and a brief guide to people who want to print it. Please consider this profile with this lense. I also want to thank the original creators and give them appropriate credit which is why I point you to those original models in this briefing.

Comment & Rating (12)

Please fill in your opinion
(0/5000)

Print Profile
0.16mm layer, 2 walls, 15% infill
Great print! lots of pieces and it can be a little confusing to assemble but once I organized everything I was able to figure it out.
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
I had to print some plates multiple times because of adhesion issues but I also did not want to use brim for most plates. The savers did not fit the handles - dunno why. I needed a drill and sand paper. At the end the model came out great. a kit card version would be the dream.
(Edited)
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Reprinted some pieces with brim cause of bad adhesion
(Edited)
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
quedó muy bien
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
1
Reply
Do you have an assembly video of any kind? I see the one on dummy 13 but the pieces look different and I am not sure what's what.
The designer has replied
1
Reply
Hey there, thank you for the feedback, there are only two differences vs the original Dummy13 the shoulders, and the chest plate. The Chest Plate is formed by two pieces on plate number 3 (See the pics attached for assembly) (Not a perfect fit). I suggest to follow the Dummy 13 video, and then when you get to the chest use the one in this plate and when you get to the shoulders you use the ones provided. I'm attaching pictures for guidance. I hope this helps!
0
Reply
Replying to @Mythmarco :
thank you for the help
1
Reply
Boosted
Print Profile
0.16mm layer, 2 walls, 15% infill
sehr cool 👍
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
1
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
1
Reply