焊锡丝支架(Solder wire bracket)

Copyright Claim

焊锡丝支架(Solder wire bracket)

Boost
18
35
14

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 4 walls, 20% infill
0.2mm layer, 4 walls, 20% infill
2.9 h
2 plates
5.0(1)

Boost
18
35
14
0
50
5
Released

Description

This is my second work. If you have any comments, please let me know and I will take them.

 

Firstly, this model is adapted to 500g solder wire with a width of 6cm

Secondly, the bottom has been designed with a hollow out, which can be embedded with 4 magnets with a diameter of 5mm (to avoid the weight reduction and dragging displacement of the solder wire after use)

 

Design with three holes for pulling solder wire at different angles

 

After installing the magnet, it can be adsorbed on the hot air gun box or other iron parts

 

Printing does not require support and can be formed as a whole. Convenient and fast.

---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

这是我第二个作品,大家有什么意见可以和我说,我会采纳。

首先:这个模型是适配500g焊锡丝,宽度为6cm
其次:底部做了镂空设计,可以镶嵌4颗直径5mm的磁铁(避免焊锡丝快使用完后重量变轻,拖拽位移)

设计有三个孔洞,以供不同角度的拉取焊锡丝

装完磁铁后,可以吸附在热风枪盒子上或者其他铁的部分

打印不需要支撑,一体成型。方便快捷

Comment & Rating (14)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 4 walls, 20% infill
Nice🤩
1
Reply
你这个焊锡丝太小了,看起来这焊锡丝是有铅的,建议使用无铅并且带松香的会比较好用
0
Reply
Can you do one thing for me? i want a case for a PC fan with a coal filter for soldering
The designer has replied
1
Reply
Do you want a welded smoking device to protect your health? I've done a simple one before, but my right hand is broken and I won't be able to do it for a while. It'll take about a month.
1
Reply
If it is to absorb solder smoke, I do not recommend the use of computer fans, I recommend you buy a violent fan, 12v brushless motor, 4cm wide, 2cm thick. It's relatively portable.
1
Reply
It works great, but it gets loud. I will design the circuit so that you can use the 18650 power, or the phone charger power
1
Reply
这里有人上传的打印配置文件,我的建议是百分百填充。很轻的支架,在焊锡丝消耗到一定程度没加装磁铁是有可能会被拖动影响使用
The designer has replied
1
Reply
Print Profile fixed
1
Reply
Replying to @Kilr0y :
good
0
Reply
Replying to @Kilr0y :
推荐百分百填充,个人建议,因为我看了磁体并不便宜,并不是一个好方法。如果你使用后发现支架被拖着走,可以在底座固定4个螺丝
0
Reply
thank you for Sharing this model! already collected it
The designer has replied
1
Reply
Small problem, I hope my good brother, when you have other models in the future, I will help you realize them.
0
Reply
使用后有什么不良的使用情况记得告诉我,我会做进一步的修改,毕竟每个人使用的习惯都不一样
0
Reply
No more