Abbau Hammer Bruder Bagger

Copyright Claim

Abbau Hammer Bruder Bagger

Boost
5
9
7
GIF

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
3.2 h
3 plates
5.0(2)

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
3.4 h
1 plate
5.0(1)

0.16mm layer, 4 walls, 40% infill
0.16mm layer, 4 walls, 40% infill
Designer
22 min
1 plate
5.0(1)

Boost
5
9
7
2
10
8
Released

Description

Abbauhammer für Bruder Rad und Raupen Bagger welcher mit und ohne Magnete verwendet werden kann.

 

Ohne Magnet:

Bei dem Zusammenbau, muss die Schraube bis nach unten auf den Spitz geschraubt werden. Somit ist er Fix und nicht beweglich.

 

Mit Magnet:

Beim Zusammenbau, müssen die Magenete der grösse 10mm x 10mm in die Spitze und in die Schraube gedrückt werden, wie auf dem Bild ersichtlich. Die Magnete müssen sich gegenseitig abstossen. Danach die Schraube eindrehen bis die gewünschte Vorspannung erreicht ist.

 

Alternativ kann auch eine Feder verwendet werden.

 

Zum Einschrauben der Schraube wird ein Handelsüblicher Innensechskant-Schlüssel 8mm benötigt, der auch ausgedruckt werden kann.

 

------

 

Dismantling hammer for Bruder wheel and crawler excavators which can be used with and without magnets.

 

Without magnet:When assembling, the screw must be screwed down to the tip. So it is fixed and not movable.

 

With magnet:When assembling, the magnets measuring 10mm x 10mm must be pressed into the tip and into the screw, as shown in the picture. The magnets must repel each other. Then screw in the screw until the desired preload is achieved.

 

Alternatively, a spring can also be used.

 

To screw in the screw, a standard 8mm Allen key is required, which can also be printed out.

Comment & Rating (7)

Please fill in your opinion
(0/5000)

Print Profile
0.16mm layer, 2 walls, 15% infill
echt super! danke!
The designer has replied
0
Reply
Bitte gern geschehen😃 Würde mich sehr über einen Boost Token freuen. Danke und viel Spass damit😃
0
Reply
Boosted
Print Profile
0.16mm layer, 4 walls, 40% infill
The designer has replied
2
Reply
thank you very much for the rating👍🏻😃 I would be very happy about a boost token😃 thank you
(Edited)
1
Reply
Boosted
Print Profile
0.16mm layer, 2 walls, 15% infill
2
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
The designer has replied
0
Reply
thank you very much for the rating👍🏻😃 I would be very happy about a boost token😃 thank you
0
Reply
No more

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.