Coin showcase Plug-in system (coin holder)
Coin showcase Plug-in system (coin holder)
Print Profile(1)
Description
Description
Coin showcase Plug-in system (coin holder).
(Directions for customization are below)
A system with which you can display coins from all over the world. The individual pieces can be put together and rotated in many different ways to create a customized arrangement. How to print the individual pieces is described below.
Currently Available:
More will be added as time goes on, or send me a request with the diameter and thickness of your coins (use a caliper) and I will upload models for your coins.
| Diameter (mm) | Diameter (inch) | Thickness (mm) | Thickness (inch) | Print Plate |
| 26,00 | 1,0236 | 1,60 | 0,0630 | A3 |
| 21,00 | 0,8268 | 1,50 | 0,0591 | A1 |
| 27,00 | 1,0630 | 1,20 | 0,0472 | A4 |
| 23,00 | 0,9055 | 1,80 | 0,0709 | A2 |
| 16,00 | 0,6299 | 1,7 | 0,0669 | A5 |
| 19,00 | 0,7480 | 1,7 | 0,0669 | A6 |
| 21,00 | 0,8268 | 1,7 | 0,0669 | A7 |
| 20,00 | 0,7874 | 1,9 | 0,0748 | A8 |
| 22,00 | 0,8661 | 2,10 | 0,0827 | A9 |
| 24,00 | 0,9449 | 2,40 | 0,0945 | A10 |
| 23,00 | 0,9055 | 2,30 | 0,0906 | A11 |
| 26,00 | 1,0236 | 2,20 | 0,0866 | A12 |
| 19,00 | 0,7480 | 1,50 | 0,0591 | A13 |
| 21,00 | 0,8268 | 1,90 | 0,0748 | A14 |
| 18,00 | 0,7087 | 1,30 | 0,0512 | A15 |
| 24,00 | 0,9449 | 1,70 | 0,0669 | A16 |
| 31,00 | 1,2205 | 2,10 | 0,0827 | A17 |
| 26,00 | 1,0236 | 2,00 | 0,0787 | A18 |
Directions:
1. Measure the diameter and thickness of your coin. (Best with a caliper)
2. Round up or down and find the suitable model in the table above. (⌀24,22 mm Thickness: 1,74mm → take model with ⌀24mm and 1,7mm)
3. Open the correct print profile in Bambu Studio (table shows the print plate where you can find the model) and select the correct print plate.
4. Decide which connections you need (top, bottom, sides)
5. Go to Objects (make sure that you are on the correct plate)
6. When you need the outgoing pins change nothing. When you don't need one outgoing pin select […].stl_1 or […].stl_3; right click; click on “Change type”; select “Negative Part”; and click OK. (This part will then not be printed.)
7. When you don't need the holes on the top or the side change nothing. When you need one or both holes change the parts […].stl_4 and […].stl_6 or […].stl_5 to Negative Part (like in Step 6.)
8. Check in the Preview if everything is correct and print it. (Would recommend Bed Leveling and Flow Dynamics Calibration)
Tip: You can duplicate the the piece and print two or pull another model on to the same print plate. (recommend changing “Print sequence” to “By object”)
Happy printing!
When you see where I can make improvments just write them in the comments.
Comment & Rating (1)
License
