Mandala Coaster

Copyright Claim

Mandala Coaster

Boost
140
181
24

Print Profile(4)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

Mandala Coaster - Version 1
Mandala Coaster - Version 1
Designer
1.2 h
1 plate
4.9(9)

0.16mm layer, 2 walls, 15% infill
0.16mm layer, 2 walls, 15% infill
Designer
3.4 h
3 plates
4.8(5)

Mandala Coaster - Version 3
Mandala Coaster - Version 3
Designer
1.1 h
1 plate
5.0(2)

Mandala Coaster - Version 2
Mandala Coaster - Version 2
Designer
1 h
1 plate
5.0(1)

Boost
140
181
24
15
141
118
Released

Description

Designed 3 coasters with mandala effect :)

I printed them with AMS and it takes about 1 hour to print each coaster.

 

The size of each coaster is 95mm x 95mm x 2.40mm

 

Before you send it to your printer, check that the bottom of the coaster is sliced properly with the correct colors. The bottom side is the side with the drawing and the top should be in plain color.

 

For example, this is the top view after the slice:

Top view after slice

 

This is the bottom view after the slice:

Bottom view after slice

 

Hope you enjoy and share your printings :)

Comment & Rating (24)

Please fill in your opinion
(0/5000)

pla glitter with pla silk (purple) looks amazing
The designer has replied
2
Reply
Awesome color combinations! Thanks for sharing :)
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
small issues but that might be more down to my bed adhesion, not sure. though other prints have been fine
The designer has replied
0
Reply
Have you tried increasing the flow rate? Did you also check that the wall generator is at arachne mode?
0
Reply
Replying to @seanyasno :
I just printed with the designer print profile, didn't tweak anything at all 😅 But in all likelihood it's just my bed adhesion that caused this But I appreciate you trying to help, it's great to see! I'll definitely be printing more, I'll add more successful Makes for you too ;)
(Edited)
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Amazing coasters! Printed all 3. Gifted one to a friend because he really liked them. The other 2 fit into my Nissan Frintier's non-standard car cup holders perfectly without the need of rescaling. Thank you!
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Printed with Bambu matte black and Ziro tri-color matte rainbow filament on a PEY build plate, this model came out absolutely beautiful.
0
Reply
Print Profile
0.16mm layer, 2 walls, 15% infill
Awesome design. Great Print. Thanx
The designer has replied
1
Reply
Thanks, glad you liked it :)
0
Reply
Print Profile
Mandala Coaster - Version 1
it worked as intended but I probably used the wrong colors. 😅 some corners have voids.
The designer has replied
0
Reply
Did you change the wall generator to arachne? Did you try to increase the flow rate?
0
Reply
Boosted
Great design.
0
Reply
Boosted
Print Profile
Mandala Coaster - Version 1
snygga underlägg. Går att skriva ut med 0.6mm men då förloras en del detaljer. Nice looking coasters, is printable with 0.6mm nozzle, but then small detaljs get lost.
(Edited)
0
Reply
Print Profile
Mandala Coaster - Version 3
printed one of each version for my wife in three different primary colors. She loved them.
0
Reply
Print Profile
Mandala Coaster - Version 1
0
Reply