Drill Spool Winder

Drill Spool Winder

Boost
31
84
33

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

0.16mm layer, 6 walls, 25% infill
0.16mm layer, 6 walls, 25% infill
Designer
3.9 h
1 plate
4.8(26)

Open in Bambu Studio
Boost
31
84
33
22
302
214
Released

Description

Just a simple tool for respooling filament. should fit most power drills with a chuck. use in combination with 1 or 2 spool rollers for ease, I use my sunlu s2 for the donor roll and just hold the new roll

Comment & Rating (33)

Please fill in your opinion
(0/5000)

Print Profile
0.16mm layer, 6 walls, 25% infill
Didn't work with the Sunlu brand of spool, works with my Bambu
1
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
You have to put on 50% speed otherwise it won’t print
The designer has replied
0
Reply
your the first one to have that issue. maybe it's not the speed that's the problem
0
Reply
check that all your cooling fans are working properly. make sure your filament matches the profile and that your filament is dry. and make sure your printer is properly prepared( ie glass open/closed, clean and prepared print bed, all routine maintenance has been performed and so on)
0
Reply
see all other ratings for this model and profile
0
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
Someone already made this comment but I could not agree more : please edit the model and round the edges. My hand hurts lol
The designer has replied
2
Reply
I appreciate the feedback, hopefully I'll have time to update the model soon
0
Reply
i will say the one complaint i have is the edges are sharp and painful to screw and unscrew had to file them down other than that it's great
The designer has replied
1
Reply
thank you for the constructive feedback!
0
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
Einfach super funktioniert einwandfrei
2
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
Rewinding other filament in smaller quantities works flawlessly with a small screwdriver
Show original
1
Reply
Thanks! Worked well! .. except I think I was going to fast and got out of round a little because the shaft sheered off. No biggie. I just used what was left of the shaft and will print another. Bonus! I took apart the bambu reel after winding the Prusa ABS filament onto it and then realized I hadn't removed the RFID tag for Bambu PLA :( So! I used the winder to tighten down the filament back onto the spool so that I could twist the spool back closed after taking it apart to remove the RFID tag. We'll see if it prints. If not, I'll have to transfer it again to another bambu spool Thanks!
1
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
Needs support brim
1
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
A quick and simple design that prints well and is perfectly sufficient for me, thank you very much.
Show original
1
Reply
Print Profile
0.16mm layer, 6 walls, 25% infill
this thing works great. I wish I could find one that could help me. re-roll the spools easier, but this thing worked perfect and I used it the other day to wind some microfiber thread to clean my printer as z axis rods
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.