HexStorage V2 Large
Copyright Claim
HexStorage V2 Large
Boost
262
442
80
Print Profile(4)
My recommendation | Fixed Bottom
Designer
29.6 h
4 plates
0.2mm layer, 2 walls, 15% infill with brim
7 h
1 plate
0.2mm layer, 2 walls, Gyroid 15% infill, 90-degree Bridge Setting
6.4 h
1 plate
0.6mm nozzle, 0.3mm layer, 2 walls, 15% infill
28.7 h
4 plates
Boost
262
442
80
6
742
573
Released
Description
Updates:
31-10-2023 - New version with a better printing bottom, sorry to everyone that had problems.
05-11-2023 - The handles should now print better. :)
Stackable hexagon storage box V2 Large
A model with supports for the handles is provided because all printers cant handle the long bridge for the handles.
The Bambulabs P1P could handle the handle bridge without problem but my V400 couldnt so pick the supported version if you want to be safe. :)
A big upgrade in both aesthetic and strength for a little more filament.
For different sizes look at my profile and for a model with less filament use look at the V1.
Dimensions:
250*200*100mm / 250*200*150mm
Comment & Rating (80)
All
Hey! Awesome design :) Thanks a lot!
I thought about making them fit inside of an Eurocrate / Eurobox /container.
The Inner dimensions (at the Bottom) from a Standard 60x40cm Eurobox are 550mm x 350mm.
Do you thinks ist possible to just scale them accordingly, or would ist mess up the print?
Again: thanks a lot!
Bensi
The designer has replied
1
Reply
Hello! Thank you for the intereset in my boxes :)
If you scale them a little bit it would probobly work but too much and the walls might get too thin so if you want a specific size it would probobly be easier for me to make it :)
(Edited)1
Reply
Replying to @OlleMark
that was a fast reply :o
I see, I will try to scale them a bit, will post my results.
if you have the time and energy to make a set of eurobox compatible crates it would mean a lot!
1
Reply
Replying to @makerAcademy_BS
Yeah i can do that! :)
What exact measurements do you want? (in metric)
1
Reply
Print Profile
My recommendation | Fixed Bottom
prints fine
The designer has replied
1
Reply
Thank you very much! :D
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill with brim
good size tray, don’t like the bottom of the tray, would prefer it flat.
1
Reply
Thank you for the feedback! i will make the bottom print better. :)
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill with brim
printed well with recommended settings for the p1p
1
Reply
Print Profile
My recommendation | Fixed Bottom
Really great design. saved filament with hexagon design
0
Reply
Print Profile
My recommendation | Fixed Bottom
Great 3d job.
0
Reply
Print Profile
My recommendation | Fixed Bottom
i had some smaller issues with stringing. not a big deal. The box is great!
0
Reply
Print Profile
My recommendation | Fixed Bottom
Very nice design and print. The Support was easy to remove.
0
Reply
Hi OlleMark, is it possible to create a lid for these Hex Storage boxes?
The designer has replied
1
Reply
Oh that's absolutely possible! Would you want a closed lid or with the hexagon pattern? 😊
0
Reply
Replying to @OlleMark
Closed lid would be best please. Thanks
1
Reply
Replying to @Dark3D
The lid is now available here :) https://makerworld.com/en/models/75205#profileId-79699
(Edited)
2
Reply
Print Profile
My recommendation | Fixed Bottom
0
Reply
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld