MT VICE - Rotate & Tilt Model Painting Vice by Peter Martin

Peter Martin

Tools>Other Tools

GIF

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

MAIN PARTS 0.2mm layer, 5 walls, 25% infill

Designer

10.8 h

2 plates

4.8(5)

ACCESSORIES 0.2mm layer, 5 walls, 25% infill

Designer

6.7 h

3 plates

5.0(2)

Open in Bambu Studio

Boost

168

127

Released

Description

ROTATING & TILTING MODELLING VICE

Before putting together read through the assembly instructions attached, thanks.

Designed for holding models in place while painting. Table holds model firmly in place and is easily rotated / Tilted to aide painting your model. You can lock the rotation or tilt at any point.

Uses a single winding arm and is smooth in its operation with a strong hold.

Besides the files you will need 2 x M5 x 10mm bolt , although I have included a bolt you can print that will work if your careful when fitting, also a small screw to hold on the Knob for the main bolt.

I have included a smaller set of clamps for holding small models, they are 10mm high instead of the standard 17mm high.

The Main Bolt,the Rotation Locking Screw and the Paint Tray require supports, all other items print fine without them.

I have created a couple of accessories so far.

The Attachable Paint Tray

THE WEIGHTABLE BASE

Documentation (1)

Assembly Guide (1)

Assembly Instructions MT VICE ROTATING_06a3bedf-adab-4b5b-ab6f-e8cfea797170.pdf

Comment & Rating (18)

@PE12KSY

Boosted

Print Profile

ACCESSORIES 0.2mm layer, 5 walls, 25% infill

best model I’ve ever downloaded from here. this is an absolute must for anyone who paints miniatures, craft etc. boosted!

The designer has replied

@PMMzero

Thanks, appreciate it.

@eric.w.deagle

Boosted

Print Profile

ACCESSORIES 0.2mm layer, 5 walls, 25% infill

Excellent print and very useful.

The designer has replied

@PMMzero

Thanks

@eric.w.deagle

Boosted

Print Profile

MAIN PARTS 0.2mm layer, 5 walls, 25% infill

no issues at all! everything printed and fit perfectly!

The designer has replied

@PMMzero

thanks for the review, glad your getting use out of it. Peter

@PE12KSY

Boosted

Print Profile

MAIN PARTS 0.2mm layer, 5 walls, 25% infill

excellent! boosted

@mavy47

Fantastic model. Can't wait to put this to use as I've been putting off assembling and painting my Starwars & Mandalorian models, and might get into minifigs too! Well done! I wish I had boost tokens right now or I'd boost this for sure!

The designer has replied

@PMMzero

Hope it works well for you, thanks for the comment.

@mavy47

Replying to @PMMzero :

Will post an update when my filament finally arrives.

(Edited)

@user_1971152265

Boosted

Well-designed and practical

The designer has replied

Show original

@PMMzero

Thanks

@dj35042

That’s going to be the best rc truck work stand I’ve ever seen! Thanks for sharing and great idea!

@bossen

Boosted

Hi Peter, Where can I find The Attachable Paint Tray? I can see you have one in your collection, but thats not attachable or? BR. Mogens - Denmark

The designer has replied

@PMMzero

Hi, its on plate 2 of the Accessories Print Profile. It has 2 threaded protrusions that just slot into the holes on the main table and you use the two nuts to hold in in place. If you watch the gif video you'll see what I mean. Hope that makes sense.