Xeno Trophy
Copyright Claim
Xeno Trophy
Boost
116
156
27
Print Profile(2)
0.6mm nozzle, 0.18mm layer, 2 walls, 8% infill
Designer
16.4 h
4 plates
0.4mm nozzle, 0.2mm layer, fixed teeth/connections, new base
19.1 h
6 plates
Open in Bambu Studio
Boost
116
156
27
18
212
80
Released
Description
I saw that idea originally at JackOfTheDust website. They making limited sculptures with crazy ideas. Usually sold out as it appears.
Used the head model of PrintedObsessio's Xenomorph as a guide.
It needs lot of supports and will benefit from the upcoming Prusaslicer's new organic support feature.
For the rod I originally planned a 8mm linear rod, but added an option to print it.
If you print the rod.. print it laying on the bed.
Comment & Rating (27)
All
Boosted
Print Profile
0.6mm nozzle, 0.18mm layer, 2 walls, 8% infill
Great model, easy print. Resized a little to fit my A1 mini. only issue is that the little pegs between the two head sections were a bit too long for a tight fit. File them down a good bit, and you're golden.
The designer has replied
0
Reply
Nice make! Thanks for sharing. To be honest I did not tested the pegs. And I guess because the overhangs in the holes they are too long indeed. Will review that. Sorry for inconvenience.
0
Reply
Boosted
Replying to @Grafitomi
It wasn't a big deal. Took a couple minutes to file down. I didn't have to be terribly precise, as they're just used to line up the two halves. Just as long as it protrudes a little so it can locate in the other side.
0
Reply
Boosted
Replying to @Grafitomi
Made some progress. Automotive primer/filler, and then a pretty decent glossy piano black rattle can paint job. Made a walnut plaque. Going to mount it when the paint is dry.
0
Reply
Boosted
Easy print love my Xeno model. I’m so excited so finally have 1 now.
(Edited)
The designer has replied
0
Reply
Niceee! :) congrats, and thanks for the boost
0
Reply
Print Profile
0.4mm nozzle, 0.2mm layer, fixed teeth/connections, new base
I used transparent petg for the teeth
The designer has replied
0
Reply
Boosted
That looks awesome, I might need to try that!
0
Reply
Boosted
Print Profile
0.4mm nozzle, 0.2mm layer, fixed teeth/connections, new base
Amazing model, contemplating painting him but looks great in just black and white.
0
Reply
Boosted
Print Profile
0.6mm nozzle, 0.18mm layer, 2 walls, 8% infill
(Edited)
The designer has replied
1
Reply
Awesome print! and thanks for the Boost!! 🙏🏻
0
Reply
Boosted
Printed this out over the last couple of days on my A1 Mini. Had to shrink it down just a little to fit, but it looks great. Going to sand, prime, and paint it, and then I'm going to make a shield mount and put it on the wall like a taxidermied deer head.
0
Reply
Boosted
Great model!
The designer has replied
1
Reply
Glad you like it! also…Thanks for the boost.
0
Reply
Boosted
Great work
The designer has replied
1
Reply
thanks for the boost! 🙏🏻
0
Reply
Boosted
Love the model. I just uploaded a new print profile with a beefer base. The original one had a hard time holding up the full-sized head. I also printed the support vertically, for better rigidity and strength. I also cut the teeth and connection pieces a bit.
1
Reply
Boosted
Print Profile
0.4mm nozzle, 0.2mm layer, fixed teeth/connections, new base
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivativesRelated Models
© 2024 MakerWorld