A1 Mini Stand with Drawer and Build Plate Holder

Remixed by

A1 Mini Stand with Drawer and Build Plate Holder

Remixed by
Boost
57
110
11

Print Profile(4)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

Main model, 0.2mm layer, 3 walls, 15% infill
Main model, 0.2mm layer, 3 walls, 15% infill
Designer
28.2 h
6 plates
4.8(8)

Lid for accessories box, 0.2mm layer, 2 walls, 15% infill
Lid for accessories box, 0.2mm layer, 2 walls, 15% infill
Designer
33 min
1 plate

Lego_Base_Plate, 0.2mm layer, 4 walls, 15% infill
Lego_Base_Plate, 0.2mm layer, 4 walls, 15% infill
Designer
59 min
2 plates

Hygrometer Holder, 0.2mm layer, 2 walls, 15% infill
Hygrometer Holder, 0.2mm layer, 2 walls, 15% infill
Designer
21 min
1 plate

Boost
57
110
11
7
113
31
Released

Description

A remix of @筋斗云の点线面 's great design

Key changes:

  • Height reduced by approximately 15%, now only 6cm tall.
  • Filament usage and print time also reduced drastically.
  • Drawer assembly redesigned, can't tell it‘s made of two parts now.
  • Dimensions and gaps adjusted, smooth damping effect when sliding drawers.
  • The outermost compartment of the drawer suitable for glue.
  • Compartment reserved for original accessory box, and usable space above its lid.
  • Hold spare build plate better as a ‘clip’ mechanism on the end of the slot.
  • It will be more accessories like inserts for the drawer or hygrometer holder etc.

Print guideline:

Manual organic tree support for Base part1&2, minimal 3walls and 15% gyroid infill.

For certain materials, it seems like a good idea to add a brim out of caution.

Can only print with P1P/P1S/X1C, not planning version for A1 mini as the model just too big to fit.

PS: You Should attach some shock-absorbing foam or rubber pads under the base to reduce vibrations.

 

Remix 自 @筋斗云の点线面 大佬的 A1mini-底部抽屉

主要变化:

  • 高度降低15%至约6厘米,大幅缩减了材料用量和打印时间
  • 抽屉的装配形态重新设计,你几乎无法分辨是两部分组成
  • 尺寸和间隙精细调整过,现在抽屉插入时阻尼感非常好
  • 抽屉最外侧特别适合放竹子的胶水,这胶水真的 YYDS
  • 预留了匹配原厂配件盒的格子,并且盖上后还可以放小东西
  • 可以储存两个备用打印板,并且插入后后端会被固定住不会乱晃
  • 会有更多的配件更新,如抽屉内分割,湿度计支架等等

打印注意事项:

主体框架部分请使用手动有机树状支撑(已设好),3墙,15%螺旋填充,根据自身情况决定是否添加 Brim

只能使用 P1P/P1S/X1C 打印,暂不考虑修改 mini 可打印的版本,模型实在是太大了,勉强分件效果也不会好。

注意:请在底座反面贴一些减震泡棉或橡胶脚垫以减少打印时的震动,经测试效果甚至比直接把机器放在桌上时还好。

Comment & Rating (11)

Please fill in your opinion
(0/5000)

Great design It is little oblivious were I split the model in order to use my A1 mini But for me it doesn’t matter It stil perfect
0
Reply
could you post your STL file please?
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
Tolles Modell, leider gab mit dem Druckprofil ein paar Problemchen (Supports nicht gut zu lösen, Warping, Schublade geht hinten leicht und hinten schwergängig). Habe es nun aber einigermaßen hingekriegt. Die Lösung zum Zusammenstecken, find ich richtig klasse. Danke!
1
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
Boosted
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
easy to print and very useful.
The designer has replied
0
Reply
Hey, thanks so much for the great feedback! Would you mind sharing some photos? Would be really helpful for others in the community. Thanks again for the support! 😆
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
Print Profile
Main model, 0.2mm layer, 3 walls, 15% infill
0
Reply
No more