Nail Shark - Nail Clipper Catcher by christofer.jh

christofer.jh

Tools>Medical Tools

Print Profile(3)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.16mm layer, 2 walls, 15% infill

Designer

22 min

1 plate

4.9(16)

no fins - 0.16mm layer, 2 walls, 15% infill

Designer

43 min

2 plates

4.5(4)

2 Sizes 0.2mm layer, 2 walls, 15% infill

24 min

1 plate

5.0(3)

Open in Bambu Studio

Boost

134

167

188

190

Released

Description

Tired of nails flying every where when you clip them?

Introducing, the nail shark.

Let the hungry shark eat your nails, no more flying nails everywhere!

Fits most normal sized nail clippers, snap or slide on.

Boring adult that think the fins look unnecessary? Well, now the white shark have its fins folded up!

Comment & Rating (36)

@quintenmyth

Print Profile

0.16mm layer, 2 walls, 15% infill

Printed well, unfortunately doesn't seem to fit my clippers as the clippers have a slight curve in the bottom side. I like the concept so I'll look for other clippers or redesign

(Edited)

The designer has replied

@christofer.jh

in what way does it not fit? is it loose, or don't clip on at all?

@quintenmyth

Replying to @christofer.jh :

I can't slide it on, the widest part of the clipper is not at the front. I added a picture to clarify. The dimension between the two vertical walls in the design is 0.2 mm smaller than the widest part on the bottom of my clipper (I assumed it was intentional to enable press fit)

@christofer.jh

Replying to @quintenmyth :

ah, I see! could you measure the widest part? Some simple x-scaling in bambu studio will probalby work

@ogscar

Print Profile

0.16mm layer, 2 walls, 15% infill

very nice. was a bit difficult too put on because of the rivet on the underside, but fit very well once in place. put it on from the backside as if the shark is eating the nail clippers.

The designer has replied

@christofer.jh

Great explanation of the assembly, imma use it!

@MrBurrito

Boosted

Print Profile

2 Sizes 0.2mm layer, 2 walls, 15% infill

Works perfectly! Thank you for sharing this!

(Edited)

@mateibocancios

Print Profile

no fins - 0.16mm layer, 2 walls, 15% infill

Works good.

@botboy23

Print Profile

2 Sizes 0.2mm layer, 2 walls, 15% infill

Works well and luckily fit my clippers

@NickApostolakis

Print Profile

0.16mm layer, 2 walls, 15% infill

printed nice and fit nice as well

@Kopp3D

Print Profile

2 Sizes 0.2mm layer, 2 walls, 15% infill

The smaller one works great!

@jarron268

Print Profile

no fins - 0.16mm layer, 2 walls, 15% infill

the print turned out good but it did not fit my clippers

The designer has replied

@christofer.jh

that sounds like 5 stars... ;)

@jarron268

Replying to @christofer.jh :

my clippers are 14.4mm the same size as the print says and still too tight

@christofer.jh

Replying to @jarron268 :

Ah, fair enough! Did you try to "slide it on", and not press it on?

@marcorei

Print Profile

0.16mm layer, 2 walls, 15% infill

Fun design! I printed mine out of PLA matte and unfortunately it broke when clipping the clipper in. But a less brittle material probably works fine.

The designer has replied

@christofer.jh

I find it much easier to "slide" the clipper in, from the back.

@Adaks

wow, i left a review saying that it's not reliable and it was removed? lol its true, there are still gaps which results in pieces flying out, even after it being scaled properly

The designer has replied

@christofer.jh

hello, I don't know why your comment was removed? However for me the small gaps have not let any pieces flying away, but it's hard to design for something that is not the same dimensions for everyone. Edit: I double checked my history and I have not reported any comments or reviews for this model.

(Edited)